Brake Caliper Pin Grease
#1
Junior Member
Thread Starter
Join Date: Mar 2013
Location: Flower Mound, TX
Posts: 241
Total Cats: 27
Brake Caliper Pin Grease
I just move up to big boy brake pads (HP+ to DCT 60/30) and wonder what to use for Caliper Pin Grease. Hawk doesn't put the packets of grease in the DCT 60/30s.
I have some NAPA Silicone Brake Lube, but it says it's good to only 600F.
Is that adequate or is there something better for TRACK applications?
I have some NAPA Silicone Brake Lube, but it says it's good to only 600F.
Is that adequate or is there something better for TRACK applications?
#4
I've been wanting to try some of this stuff, look at the temp range.
Specialty Lubricants - Anti-Seize : Permatex® Anti-Seize Lubricant
Specialty Lubricants - Anti-Seize : Permatex® Anti-Seize Lubricant
#6
Elite Member
iTrader: (2)
Join Date: May 2007
Location: Cromwell, Connecticut
Posts: 2,606
Total Cats: 16
I've been wanting to try some of this stuff, look at the temp range.
Specialty Lubricants - Anti-Seize : Permatex® Anti-Seize Lubricant
Specialty Lubricants - Anti-Seize : Permatex® Anti-Seize Lubricant
That's just pretty standard antiseize. Use it at work non-stop. Great for stainless hardware into stainless. It isn't really sticky enough to last on the caliper pin IMO
#7
Most anti-seize I've used in high temp applications the base oil/grease that makes it goopy evaporates/burns off and it turns into just powder. Not sure if your brake sliders are going to get that hot though.
I use the dominator on my car, the normally needs to be refreshed every few races or it turns into paste. But that could be due to mixing with at least 3 different greases in the slide pin area and me being too lazy to clean it all out. Just got to milk this brake setup along for another season before upgrading.
I use the dominator on my car, the normally needs to be refreshed every few races or it turns into paste. But that could be due to mixing with at least 3 different greases in the slide pin area and me being too lazy to clean it all out. Just got to milk this brake setup along for another season before upgrading.
#9
If using anti-seize, wouldn't the copper stuff hold up better? It's rated to 2000°.
3M Copper Anti-Seize Brake Lube 08945
3M Copper Anti-Seize Brake Lube 08945
#10
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
You should already have a tube of the Amsoil Race2000/Dominator anyway for doing your hubs. You can put it in your coffee in the morning and be regular just like Hustler.
But seriously, its amazing stuff. I even used it as tap compound yesterday
But seriously, its amazing stuff. I even used it as tap compound yesterday
#11
Elite Member
iTrader: (1)
Join Date: Jun 2006
Location: Warrington/Birmingham
Posts: 2,642
Total Cats: 42
If using anti-seize, wouldn't the copper stuff hold up better? It's rated to 2000°.
3M Copper Anti-Seize Brake Lube 08945
3M Copper Anti-Seize Brake Lube 08945
#15
I've used Permatex Ceramic Extreme Brake Parts Lubricant (Purple) before and it seemed to work well.
Someone told me it wasnt too safe for rubber bushings, so I switched to the red , but it looks like Permatex has discontinued it for whatever reason.
I'd give Amsoil a try, but I've got enough of this Permatex stuff for like 30 applications, so I might as well try and use it.
Someone told me it wasnt too safe for rubber bushings, so I switched to the red , but it looks like Permatex has discontinued it for whatever reason.
I'd give Amsoil a try, but I've got enough of this Permatex stuff for like 30 applications, so I might as well try and use it.
#16
This works pretty well on the sliders and is readily available locally
Specialty Lubricants - Brakes : Permatex® CeramicExtreme Brake PartsLubricant
Specialty Lubricants - Brakes : Permatex® CeramicExtreme Brake PartsLubricant
#18
What NOT to use; Permatex ultra disc brake caliper lube, I used it once, and luckily I checked the calipers after the track day and they were stuck solid. The pins would not move in the bushings (the rubber ones).
#19
I use Sil-glide for the slides (I think NAPA is the same). In the Data sheet it said it's rated at >600*, but no one lists a "drop point" for it. It seems to be a cheap substitute for the expensive import brake greases. It's like $7 for a huge tube.
Some of the guys I know used the Bendix "purple" (pink) Ceramlub on the sliders, but when I took my own apart after doing the same I found that the carrier had mostly evaporated and the ceramic "grease" was dry, gummy, and powdery. It seems like Bendix reformulated it, as the new jar I bought is blue and doesn't separate in the jar. I'm leery to put it on my slides again, but I still use it on the back of pads as anti-squeal. It's very sticky and doesn't wash off.
This reminds me. I need new hardware kits for my rear calipers.
Some of the guys I know used the Bendix "purple" (pink) Ceramlub on the sliders, but when I took my own apart after doing the same I found that the carrier had mostly evaporated and the ceramic "grease" was dry, gummy, and powdery. It seems like Bendix reformulated it, as the new jar I bought is blue and doesn't separate in the jar. I'm leery to put it on my slides again, but I still use it on the back of pads as anti-squeal. It's very sticky and doesn't wash off.
This reminds me. I need new hardware kits for my rear calipers.
#20
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
Now that I have a tube in my grease gun I've been tempted to use once I install my polly bushings and zerks. Anyone try this on poly suspension stuff yet?