Rotrex install loses boost
#1
Rotrex install loses boost
Hi
This is my first post on this forum, and it's regarding a Rotrex equipped car. Please be gentle.
My car is a '93 1.6, equipped with a Rotrex C15-60 charger. I'm just finishing the install right now. My problem is that the car won't hold boost. Instead, the boost vanishes completely, when the car reaches 6.5 psi (145kPa in new plots), typically at 6000rpm.
Please see the three log screenshots below from my Megasquirt. What might cause such a repetitive and total boost loss?
This is my first post on this forum, and it's regarding a Rotrex equipped car. Please be gentle.
My car is a '93 1.6, equipped with a Rotrex C15-60 charger. I'm just finishing the install right now. My problem is that the car won't hold boost. Instead, the boost vanishes completely, when the car reaches 6.5 psi (145kPa in new plots), typically at 6000rpm.
Please see the three log screenshots below from my Megasquirt. What might cause such a repetitive and total boost loss?
#3
I thought the same, so earlier today I borrowed a valve from a friend who has the same kit. Didn't chance anything.
The potential issues as I see it
1. Belt slip. However, there is no dust anywhere near the belt.
2. Boost leak. Can a leak be this systematic, causing complete boost drop at a given boost level, and then cure itself for the next pull?
3. Something wrong with the charger. I not 100% sure how it works, but is it possible for the Rotrex charger to simply stall at a certain output pressure?
4. Hose collapse. I've read stories of people experiencing inlet hoses collapsing under boost. I don't understand how that would happen.
5. ???
The potential issues as I see it
1. Belt slip. However, there is no dust anywhere near the belt.
2. Boost leak. Can a leak be this systematic, causing complete boost drop at a given boost level, and then cure itself for the next pull?
3. Something wrong with the charger. I not 100% sure how it works, but is it possible for the Rotrex charger to simply stall at a certain output pressure?
4. Hose collapse. I've read stories of people experiencing inlet hoses collapsing under boost. I don't understand how that would happen.
5. ???
#4
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,429
Total Cats: 1,207
Take the hood off and strap on a go-pro.
That or eliminate the bypass valve completely.
Rotrex is mechanically driven, it can't "stall". Belt slip might take a while to show, how much rotation are you getting out of your tensioner?
That or eliminate the bypass valve completely.
Rotrex is mechanically driven, it can't "stall". Belt slip might take a while to show, how much rotation are you getting out of your tensioner?
#7
The hose collapsing thing would only happen before the charger right? All the black hoses came with the kit, and the red 180deg hose is one I had sitting. I'll try to remove the red piece and see what happens.
Regarding the valve, if I just plug up the recirc circuit, would I not risk damaging the charger?
Edit, I just did a few pulls without the red hose. No change.
Regarding the valve, if I just plug up the recirc circuit, would I not risk damaging the charger?
Edit, I just did a few pulls without the red hose. No change.
Last edited by Delaney; 04-10-2017 at 06:27 AM.
#8
I just looked at the logs from the pulls with my friends valve. With his valve the two drops recorded happened at 5.6 and 5.5psi, whereas with my own valve the drops happened at 6.5, 6.4 and 6.5psi.
It's small datasets, but there seems to be a difference. This could be due to different climate conditions on two different days (?), or an actual influence of the valve itself.
It's small datasets, but there seems to be a difference. This could be due to different climate conditions on two different days (?), or an actual influence of the valve itself.
#13
True, all hoses in the kit is silicone, photo of the kit for your reference below.
The car has been away for a few days for a clutch change and ABS diagnostics, tomorrow I'll try to do repeated pulls with the two valves back to back. If the numbers mentioned above are repeated, I'll conclude that the valve is the culprit. Let's see.
The car has been away for a few days for a clutch change and ABS diagnostics, tomorrow I'll try to do repeated pulls with the two valves back to back. If the numbers mentioned above are repeated, I'll conclude that the valve is the culprit. Let's see.
#15
I have discussed the issue with the company who invented the Rotrex charger, and based on the plots, they strongly suspect belt slip. The belt setup looks like this, with the tensioner being the topmost pulley. Any suggestions for how to eliminate slip? I have sufficient tensioner travel, so that's not the problem.
To rule out the valve as the culprit, I'll do a few pulls with a strong Blow off valve later today.
To rule out the valve as the culprit, I'll do a few pulls with a strong Blow off valve later today.
Last edited by Delaney; 04-18-2017 at 11:47 AM.
#16
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
To clear something up real quick, the Rotrex uses a "hi-speed planetary traction drive" and from the documentation "The Rotrex supercharger has a dedicated traction oil circuit which ensures both lubrication, cooling and actual torque transfer." There is no direct drive inside the unit like an MP62, Paxton or Vortech and it absolutely can slip. Its got a set of rollers inside the unit that rub against each other, there is a reason the magic Rotrex juice is called "traction fluid" in the documentation. BUT you'd have to do something incredibly silly like run it with no oil to make it slip, and I suspect it wouldn't last long and you'd know it pretty quickly.
On a related note, isn't the top of the fluid reservoir supposed to be above the top of the head unit? I may be wrong, but it looks like its below in some of the pics.
On a related note, isn't the top of the fluid reservoir supposed to be above the top of the head unit? I may be wrong, but it looks like its below in some of the pics.
#19
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
Is the C15-60 inlet in this kit restricted like the old Kraftwerks kits?
#20
Interesting, I can't say I've ever seen that document. I also noticed that they now say its self priming. Then again its been a number of years since I've pawed through any of this, or the information I was given was bad (entirely plausible)
Is the C15-60 inlet in this kit restricted like the old Kraftwerks kits?
Is the C15-60 inlet in this kit restricted like the old Kraftwerks kits?
Post Project G group buys circa 2013, the compressor was the C30-74 and was not restricted. I've since replaced that compressor with the C30-94 and is also not restricted.
I have a hard time accepting belt slip as the culprit for the OP but he does have a different tensioner setup than the Kraftwerks kit so I couldn't rule it out. The other (more obvious) cause could be a loose hose clamp or silicone coupler. At a particular boost pressure it bleeds off and doesn't "re-seal" until a lower pressure. How consistent it is might not support this theory but it's not hard to check and re-tighten every clamp in the loop.