How to get more boost/power with my supercharger?
#1
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,339
Total Cats: 519
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Serious thread....
I have a 1.6L W100AX, with a 2.59:1 pulley ratio. That puts the SC at 18,000 RPMs at 6,900 engine RPMs. The SC's max continuous RPMs is 18,000, 20,000 is the absolute max it's rated for. That's a 5.5" lower ATI SC pulley, and a 2.125" upper pulley, the smallest one Whipple sells.
It makes 28.8 PSI boost at 6,900, which is as high as I've rev'd it for reliability's sake. I could rev it to 7,700, that would put the SC spinning 20,000, and probably make 30-32 PSI boost.
Is there anything else I can do to get more boost? Or more power with the boost I already have?
I have a 1.6L W100AX, with a 2.59:1 pulley ratio. That puts the SC at 18,000 RPMs at 6,900 engine RPMs. The SC's max continuous RPMs is 18,000, 20,000 is the absolute max it's rated for. That's a 5.5" lower ATI SC pulley, and a 2.125" upper pulley, the smallest one Whipple sells.
It makes 28.8 PSI boost at 6,900, which is as high as I've rev'd it for reliability's sake. I could rev it to 7,700, that would put the SC spinning 20,000, and probably make 30-32 PSI boost.
Is there anything else I can do to get more boost? Or more power with the boost I already have?
#3
Senior Member
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (1)
Join Date: Jan 2011
Location: Chattanooga, Tn
Posts: 1,234
Total Cats: 283
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
But seriously. I think you are running too much boost, possibly spinning the blower too hard.
David was making close to 400hp on basically your same setup on E85. With one fuel pump a 75mm throttle body, stock cams, off the shelf header...etc etc etc. And I think he was only spinning his 1600ax around 15,000 RPM at his 8,000 RPM redline.
David was making close to 400hp on basically your same setup on E85. With one fuel pump a 75mm throttle body, stock cams, off the shelf header...etc etc etc. And I think he was only spinning his 1600ax around 15,000 RPM at his 8,000 RPM redline.
#4
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,339
Total Cats: 519
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
But seriously. I think you are running too much boost, possibly spinning the blower too hard.
David was making close to 400hp on basically your same setup on E85. With one fuel pump a 75mm throttle body, stock cams, off the shelf header...etc etc etc. And I think he was only spinning his 1600ax around 15,000 RPM at his 8,000 RPM redline.
David was making close to 400hp on basically your same setup on E85. With one fuel pump a 75mm throttle body, stock cams, off the shelf header...etc etc etc. And I think he was only spinning his 1600ax around 15,000 RPM at his 8,000 RPM redline.
But curious why you think I'm running too much boost? I have a larger upper pulley I can run, but the car is slower everywhere with it installed and of course makes less boost. Or are you saying something is causing the high boost reading?
Yes mine and David's setups are very similar. He had a better header, I have better headwork (but stock cams) same size throttle, etc.
#5
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,339
Total Cats: 519
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I agree it needs to be tuned, I haven't touched the timing since I got it running right.
But curious why you think I'm running too much boost? I have a larger upper pulley I can run, but the car is slower everywhere with it installed and of course makes less boost. Or are you saying something is causing the high boost reading?
Yes mine and David's setups are very similar. He had a better header, I have better headwork (but stock cams) same size throttle, etc.
But curious why you think I'm running too much boost? I have a larger upper pulley I can run, but the car is slower everywhere with it installed and of course makes less boost. Or are you saying something is causing the high boost reading?
Yes mine and David's setups are very similar. He had a better header, I have better headwork (but stock cams) same size throttle, etc.
Yours you posted in my fuel system thread:
![](https://www.miataturbo.net/attachments/general-miata-chat-9/155992-what-fix-my-fuel-system-timing%2520map%2520-%2520whipple_zpszwm85abq.png?dateline=1448584592)
Mine on the car now:
![](http://i231.photobucket.com/albums/ee155/patsmx5/timing_zpste0x3zlh.png)
Granted I'm on E85, not C16. I believe E85 has a slower burn rate, so thus would want more timing.
#8
Senior Member
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (1)
Join Date: Jan 2011
Location: Chattanooga, Tn
Posts: 1,234
Total Cats: 283
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My car ran in the low 7s in the 8th on 600lb rear springs, full aero, stiff worn out A6s and a terrible 2.2 second 60' time (tc was set up for non preped surfaces and bogged at the preped strip)
Made one pass and got asked to leave.
So yea. I've got no clue where to tell you to go from here.
Made one pass and got asked to leave.
So yea. I've got no clue where to tell you to go from here.
#10
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,339
Total Cats: 519
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My car ran in the low 7s in the 8th on 600lb rear springs, full aero, stiff worn out A6s and a terrible 2.2 second 60' time (tc was set up for non preped surfaces and bogged at the preped strip)
Made one pass and got asked to leave.
So yea. I've got no clue where to tell you to go from here.
Made one pass and got asked to leave.
So yea. I've got no clue where to tell you to go from here.
#14
SADFab Destructive Testing Engineer
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/moderator.png)
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Another thing you mentioned the other day. Correct me if I'm wrong.
You said you were making like 36psi at the supercharger outlet, but the MAP was 28?
Something is totally screwy there.
You said you were making like 36psi at the supercharger outlet, but the MAP was 28?
Something is totally screwy there.
#15
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,339
Total Cats: 519
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
But on the topic of restrictions. What is there to fix? I know a custom header with larger diameter primaries would help, and cams. I don't really know what else I could do besides those two things.
#17
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,339
Total Cats: 519
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
This thread is just based off of "what can I do to make more power/boost". How to improve what I got.
#19
Senior Member
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (1)
Join Date: Jan 2011
Location: Chattanooga, Tn
Posts: 1,234
Total Cats: 283
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
See. That's the thing. You want to know how to get more power out of your setup...and you dont know how much power you are curretly making (other than a cell phone app) nor do you know how much power the current setup is capable of making.
Until you get the car properly tuned....everything else is just a total W.A.G.
Until you get the car properly tuned....everything else is just a total W.A.G.
#20
Former Vendor
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,103
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
All that money spent on turbos, superchargers, engine internals, your new Mercedes C63 that you've mentioned several times, and the hundred bucks for three pulls on a Dynojet breaks the bank?
![Party Kitty](https://www.miataturbo.net/images/smilies/birthday[1].gif)