Backpressure question
#1
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (2)
Join Date: Jun 2009
Location: Istanbul, Turkey
Posts: 3,222
Total Cats: 1,701
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I measured my exhaust system backpressure to see if things were flowing fine.
The car is a '98 ('99 for US folks), with an MP62 - 130/65 mm pulleys, 9.00:1 pistons, ported and reworked head, Skunk2 TB, custom CAI, 2001 style header and custom 2.5" exhaust with two resonators, a large Borla, and no cat.
I drilled and tapped an O2 sensor plug and installed it in the stock location. (There is a wideband O2 just downstream of the stock location.)
A copper pipe was threaded into the tapped plug, and ultimately connected to a MAP sensor that drives my boost gauge.
That way, I figured I could read and record whatever pressure is generated...
Here's how I did the pressure pick up:
![](https://www.miataturbo.net/attachments/supercharger-discussion-38/122354-backpressure-question-idtsr7.jpg?dateline=1409756141)
I thought this would be a good location for backpressure readings.
And, here's how it looks on the gauge (pic taken at idle):
![](https://www.miataturbo.net/attachments/supercharger-discussion-38/122355-backpressure-question-3stcqj.jpg?dateline=1409756141)
(All pressure values are in psi, vacuum is inHg, and temps are in C. Don't ask, it's easier for me that way)
I did one full boost (12-13 psi) run to redline in second gear, and recorded 4 psi.
Considering this is a FI setup, should I shoot for 0 psi by going with a larger header and a 3" setup?
Thanks.
The car is a '98 ('99 for US folks), with an MP62 - 130/65 mm pulleys, 9.00:1 pistons, ported and reworked head, Skunk2 TB, custom CAI, 2001 style header and custom 2.5" exhaust with two resonators, a large Borla, and no cat.
I drilled and tapped an O2 sensor plug and installed it in the stock location. (There is a wideband O2 just downstream of the stock location.)
A copper pipe was threaded into the tapped plug, and ultimately connected to a MAP sensor that drives my boost gauge.
That way, I figured I could read and record whatever pressure is generated...
Here's how I did the pressure pick up:
![](https://www.miataturbo.net/attachments/supercharger-discussion-38/122354-backpressure-question-idtsr7.jpg?dateline=1409756141)
I thought this would be a good location for backpressure readings.
And, here's how it looks on the gauge (pic taken at idle):
![](https://www.miataturbo.net/attachments/supercharger-discussion-38/122355-backpressure-question-3stcqj.jpg?dateline=1409756141)
(All pressure values are in psi, vacuum is inHg, and temps are in C. Don't ask, it's easier for me that way)
I did one full boost (12-13 psi) run to redline in second gear, and recorded 4 psi.
Considering this is a FI setup, should I shoot for 0 psi by going with a larger header and a 3" setup?
Thanks.
#2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
4 psi isn't that bad. My 540i (290 hp V8) all-stock measures about 4 psi before the first cat. They don't gain that much from a big aftermarket exhaust. (the usual ~3%)
Is the Borla a straight-through design?
Look for the bottlenecks. You should measure the backpressure at the inlet of the Borla too.
And read this
https://www.miataturbo.net/engine-pe...e2/#post754214
Is the Borla a straight-through design?
Look for the bottlenecks. You should measure the backpressure at the inlet of the Borla too.
And read this
https://www.miataturbo.net/engine-pe...e2/#post754214
#5
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
If you have no backpressure, then there is no flow.
I would bet you can get several PSI of fluctuation based on how you measure it, it's not like you're measuring still pressure inside of a pressure vessel. By correctly implementing the bernoulli principle, you may be able to change the sensor position and/or mounting technique while changing nothing else and read 0 or negative PSI.
Having minimal backpressure is not important for FI applications - it is important for Turbocharged applications. You have an FI application which is not a turbocharged application. Your aim should be to evacuate exhaust gasses most quickly/efficiently before they cool which increases density. A car with a supercharger should benefit most by using the same or similar exhaust to a high-performance N/A exhaust. Perhaps slightly larger to account for the increased volume of exhaust gas, but no so much that it comes close to the size of a turbocharged car's exhaust system.
I would bet you can get several PSI of fluctuation based on how you measure it, it's not like you're measuring still pressure inside of a pressure vessel. By correctly implementing the bernoulli principle, you may be able to change the sensor position and/or mounting technique while changing nothing else and read 0 or negative PSI.
Having minimal backpressure is not important for FI applications - it is important for Turbocharged applications. You have an FI application which is not a turbocharged application. Your aim should be to evacuate exhaust gasses most quickly/efficiently before they cool which increases density. A car with a supercharger should benefit most by using the same or similar exhaust to a high-performance N/A exhaust. Perhaps slightly larger to account for the increased volume of exhaust gas, but no so much that it comes close to the size of a turbocharged car's exhaust system.
#7
Elite Member
iTrader: (1)
Join Date: May 2009
Location: Jacksonville, FL
Posts: 5,155
Total Cats: 407
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
That doesnt sound right to me.
If the pressure sensor is connected to a pitot tube in the exhaust system, I would agree with you. But if it is a static pressure measurement coming from a port in the side of exhaust pipe, then the pressure should just represent backpressure resulting from restriction. If there is no restriction, there is no pressure, and the reading is independent of flow.
I honestly do not think any engine really benefits from back pressure, regardless of being turbo, supercharged, or NA. I am aware of how many motorcycle engines will not perform well with a straight pipe, with the argument usually being that they "need some backpressure", but I am not convinced.
My theory is that a super high performance, production engine (like a sportbike's engine) has oversized exhaust ports, primaries, secondaries, and exhaust tubing which is being used to make up for the fact that it is going to have to use a restrictive muffler. If it were being designed to operate in the same band but with a straight pipe it would be smaller diameter all along the exhaust system and would perform better.
My experience with car engines, which are not tuned-up as much, is that there is no point at which this problem exists as long as the header isnt oversized. Running a straight pipe will make more power, even if its pretty small.
I do agree with the idea that you have real incentive to go really big with turbo exhaust just because it will help with spool. Plus with the high backpressure created by the turbo, which is killing scavenging, every little bit helps, probably more so that with supercharged setups which tend to have excellent exhaust scavenging.
If the pressure sensor is connected to a pitot tube in the exhaust system, I would agree with you. But if it is a static pressure measurement coming from a port in the side of exhaust pipe, then the pressure should just represent backpressure resulting from restriction. If there is no restriction, there is no pressure, and the reading is independent of flow.
Having minimal backpressure is not important for FI applications - it is important for Turbocharged applications. You have an FI application which is not a turbocharged application. Your aim should be to evacuate exhaust gasses most quickly/efficiently before they cool which increases density. A car with a supercharger should benefit most by using the same or similar exhaust to a high-performance N/A exhaust. Perhaps slightly larger to account for the increased volume of exhaust gas, but no so much that it comes close to the size of a turbocharged car's exhaust system.
My theory is that a super high performance, production engine (like a sportbike's engine) has oversized exhaust ports, primaries, secondaries, and exhaust tubing which is being used to make up for the fact that it is going to have to use a restrictive muffler. If it were being designed to operate in the same band but with a straight pipe it would be smaller diameter all along the exhaust system and would perform better.
My experience with car engines, which are not tuned-up as much, is that there is no point at which this problem exists as long as the header isnt oversized. Running a straight pipe will make more power, even if its pretty small.
I do agree with the idea that you have real incentive to go really big with turbo exhaust just because it will help with spool. Plus with the high backpressure created by the turbo, which is killing scavenging, every little bit helps, probably more so that with supercharged setups which tend to have excellent exhaust scavenging.
#8
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
That doesnt sound right to me.
I honestly do not think any engine really benefits from back pressure, regardless of being turbo, supercharged, or NA. I am aware of how many motorcycle engines will not perform well with a straight pipe, with the argument usually being that they "need some backpressure", but I am not convinced.
My theory is that a super high performance, production engine (like a sportbike's engine) has oversized exhaust ports, primaries, secondaries, and exhaust tubing which is being used to make up for the fact that it is going to have to use a restrictive muffler. If it were being designed to operate in the same band but with a straight pipe it would be smaller diameter all along the exhaust system and would perform better.
My experience with car engines, which are not tuned-up as much, is that there is no point at which this problem exists as long as the header isnt oversized. Running a straight pipe will make more power, even if its pretty small.
I do agree with the idea that you have real incentive to go really big with turbo exhaust just because it will help with spool. Plus with the high backpressure created by the turbo, which is killing scavenging, every little bit helps, probably more so that with supercharged setups which tend to have excellent exhaust scavenging.
I honestly do not think any engine really benefits from back pressure, regardless of being turbo, supercharged, or NA. I am aware of how many motorcycle engines will not perform well with a straight pipe, with the argument usually being that they "need some backpressure", but I am not convinced.
My theory is that a super high performance, production engine (like a sportbike's engine) has oversized exhaust ports, primaries, secondaries, and exhaust tubing which is being used to make up for the fact that it is going to have to use a restrictive muffler. If it were being designed to operate in the same band but with a straight pipe it would be smaller diameter all along the exhaust system and would perform better.
My experience with car engines, which are not tuned-up as much, is that there is no point at which this problem exists as long as the header isnt oversized. Running a straight pipe will make more power, even if its pretty small.
I do agree with the idea that you have real incentive to go really big with turbo exhaust just because it will help with spool. Plus with the high backpressure created by the turbo, which is killing scavenging, every little bit helps, probably more so that with supercharged setups which tend to have excellent exhaust scavenging.
#9
Elite Member
iTrader: (1)
Join Date: May 2009
Location: Jacksonville, FL
Posts: 5,155
Total Cats: 407
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
2 strokes are borderline wizardry as far as Im concerned.
I think the 4 stroke equivalent of this would be the kadenacy effect, which is basically the inertia of the exhaust gasses exiting the cylinder creating a vacuum which helps draw more air in during the intake stroke. This is probably the biggest reason you want high velocity in the exhaust system, especially in the ports and header.
#10
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My twinscrew supercharged car used to have a JR header, and I have dyno plots showing a .5whp and 3-4wtq increase at 214whp with the header. From what I heard, exhaust isn't quite as important for supercharged cars as others, because of the exhaust being under pressure from the boost. Its still important for turbo cars due to better spool, etc. At least that's how I understand it.
That being said I'm still on the look out for an raceland header for tq and less weight.
That being said I'm still on the look out for an raceland header for tq and less weight.
#11
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My twinscrew supercharged car used to have a JR header, and I have dyno plots showing a .5whp and 3-4wtq increase at 214whp with the header. From what I heard, exhaust isn't quite as important for supercharged cars as others, because of the exhaust being under pressure from the boost. Its still important for turbo cars due to better spool, etc. At least that's how I understand it.
That being said I'm still on the look out for an raceland header for tq and less weight.
That being said I'm still on the look out for an raceland header for tq and less weight.
#14
Moderator
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/moderator.png)
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,884
Total Cats: 3,075
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Backpressure is bad on turbo cars and non turbo cars. Back pressure is only a measure of resistance to flow and not a measure of the presence of flow.
And the problem with a straight pipe on some naturally aspirated engines is that it can destroy the scavenging effect that has been carefully tuned in to the exhaust design by the manufacturer. The scavenging effect is the difference between highly prized tuned headers and just a cheap set of pretty headers that have not been created by a scientist in a lab. Math is important to engines.
And the problem with a straight pipe on some naturally aspirated engines is that it can destroy the scavenging effect that has been carefully tuned in to the exhaust design by the manufacturer. The scavenging effect is the difference between highly prized tuned headers and just a cheap set of pretty headers that have not been created by a scientist in a lab. Math is important to engines.
#15
Retired Mech Design Engr
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (3)
Join Date: Jan 2013
Location: Seneca, SC
Posts: 5,011
Total Cats: 859
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Restriction * Flow = Backpressure.
The electrical analogy is ohms law: Resistance * Current = Voltage
So, no restriction, no backpressure. No flow, no backpressure.
You want flow, so to reduce back pressure, reduce restriction.
Zero is the goal, but is not possible with an exhaust system. The OP question is what is reasonable, and Jason is trying to answer that question.
The electrical analogy is ohms law: Resistance * Current = Voltage
So, no restriction, no backpressure. No flow, no backpressure.
You want flow, so to reduce back pressure, reduce restriction.
Zero is the goal, but is not possible with an exhaust system. The OP question is what is reasonable, and Jason is trying to answer that question.
#17
SadFab CEO
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
ive read up on this quite a bit lately as it applies to n/a sbc v8s. and from what i understand, backpressure is no bueno for any and every setup. the engines need a little back pressure thing is a myth. they need scavenging, and with that comes a little back pressure. as david vizard puts it, there are more gains to be had with great scavenging and a little backpressure than no scavenging and no backpressure(like the straight pipe coming right off a head). he dedicates a whole section of one of his books to this topic. its on google books, im trying to find it.
to answer OPs question, get as close to 0 as possible while retaining scavenging and velocity. iirc on some of vizrds highly developed all out race setups he was measuring less than 0.2 psi.
Last edited by hi_im_sean; 11-29-2014 at 11:45 AM.
#19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Backpressure is HUGELY important on a turbocharged engine. Here's some nice reading on why:
https://www.miataturbo.net/engine-pe...-theory-71503/
From an exhaust standpoint, a supercharged engine is basically a normally aspirated engine with a power/flow bump. Scavenging is king, and, of course, back pressure plays a role in that. There are calculators out there that give recommended pipe diameters vs. HP. Worth a look.
In your particular case, you would get much more out of an aftermarket header mated to your existing 2.5" exhaust than you would get from a 3" exhaust by itself.
https://www.miataturbo.net/engine-pe...-theory-71503/
From an exhaust standpoint, a supercharged engine is basically a normally aspirated engine with a power/flow bump. Scavenging is king, and, of course, back pressure plays a role in that. There are calculators out there that give recommended pipe diameters vs. HP. Worth a look.
In your particular case, you would get much more out of an aftermarket header mated to your existing 2.5" exhaust than you would get from a 3" exhaust by itself.
#20
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Backpressure is HUGELY important on a turbocharged engine. Here's some nice reading on why:
https://www.miataturbo.net/engine-pe...-theory-71503/
From an exhaust standpoint, a supercharged engine is basically a normally aspirated engine with a power/flow bump. Scavenging is king, and, of course, back pressure plays a role in that. There are calculators out there that give recommended pipe diameters vs. HP. Worth a look.
In your particular case, you would get much more out of an aftermarket header mated to your existing 2.5" exhaust than you would get from a 3" exhaust by itself.
https://www.miataturbo.net/engine-pe...-theory-71503/
From an exhaust standpoint, a supercharged engine is basically a normally aspirated engine with a power/flow bump. Scavenging is king, and, of course, back pressure plays a role in that. There are calculators out there that give recommended pipe diameters vs. HP. Worth a look.
In your particular case, you would get much more out of an aftermarket header mated to your existing 2.5" exhaust than you would get from a 3" exhaust by itself.