Random/Hobby Fabrication Picture Thread...
#161
Thread Starter
Elite Member
iTrader: (8)
Joined: Dec 2008
Posts: 2,910
Total Cats: 51
From: Kingston, Ontario
The IRL borg EFR is different than the normal borg warner flange that comes on the EFR.
Vbands are nice to allow some wiggle room when designing systems and they make it easy to access the hardware... but on a mid to large frame turbo, bolted flanges are still king. (t3/t4/t6 footprints) T2 footprints are so tight for that one bolt that sits under the turbine housing that vband is much easier to access.
Im currently finishing up the third of these low mount, short runner "Absurdflow" style manifolds right now with a t2 flange for an internal wastegate EFR6258 with my specific EFR placement. Downpipe to follow. This setup will rock. If I were to build another street Miata for myself, this would be the setup I would run (maybe omit internal wastegate for external wastegate for packaging and boost control).
That said, I am waiting for a t4 twin scroll 6258 to come in for a BP manifold. That could very well become the new hotness.
#162
Thread Starter
Elite Member
iTrader: (8)
Joined: Dec 2008
Posts: 2,910
Total Cats: 51
From: Kingston, Ontario
a 1.8 short manifold for t2 EFR with downpipe
Started a 1.8 bottom mount manifold for TiAL housing while we wait for the backordered 6258 T4 twin scroll to make its way to me. (its in the mail to me right now)
Here is a collector shot pre-welding.
Started a 1.8 bottom mount manifold for TiAL housing while we wait for the backordered 6258 T4 twin scroll to make its way to me. (its in the mail to me right now)
Here is a collector shot pre-welding.
#164
Thread Starter
Elite Member
iTrader: (8)
Joined: Dec 2008
Posts: 2,910
Total Cats: 51
From: Kingston, Ontario
Welding these manifolds up. Nearly done!
T4 Twin scroll turbo EFR on hand. Im excited (I normally don't get terribly excited), there will be some serious advantages with these turbos over the t2 inlet EFR's.
The housings are really, really nice...
T4 Twin scroll turbo EFR on hand. Im excited (I normally don't get terribly excited), there will be some serious advantages with these turbos over the t2 inlet EFR's.
The housings are really, really nice...
#166
Thread Starter
Elite Member
iTrader: (8)
Joined: Dec 2008
Posts: 2,910
Total Cats: 51
From: Kingston, Ontario
its a totally different actuator bracket (off of the chra) I wouldn't put my money on it being the same. The actuator bracket is slotted on this one but the actuator bracket I have used for a t2 efr isn't.
We have the turbo position tacked for the top mounted jig. We need to spend a bit of time playing with some elbows and the collectors that we've cut to really hone in if the position is the best it can be before building a production jig.
I did order some wicked laser cut jigs for the absurdflow style manifolds that Tim sends my way being that he doesn't make them anymore. The jigs aren't cheap, but (if they work like I hope) they will really help reduce measurements required to make a manifold and give a more consistent manifold. That and I can hand the jig to someone else and ask them to cut them for me without having to be able to read technical drawings.
We have the turbo position tacked for the top mounted jig. We need to spend a bit of time playing with some elbows and the collectors that we've cut to really hone in if the position is the best it can be before building a production jig.
I did order some wicked laser cut jigs for the absurdflow style manifolds that Tim sends my way being that he doesn't make them anymore. The jigs aren't cheap, but (if they work like I hope) they will really help reduce measurements required to make a manifold and give a more consistent manifold. That and I can hand the jig to someone else and ask them to cut them for me without having to be able to read technical drawings.
#168
Elite Member
iTrader: (5)
Joined: Oct 2011
Posts: 5,687
Total Cats: 807
From: Detroit (the part with no rules or laws)
What are saturdays at work for? Making this nee carrier bearing and mounting plate for the hydroplane.
It's not dyed, it's 4.5mill Hardcoat with a Teflon coating. I've been working here 5 years and haven't seen any parts come out over 3mill without burning. This is dark, even a grinder would have a hard time getting through this. Me likey.
It's not dyed, it's 4.5mill Hardcoat with a Teflon coating. I've been working here 5 years and haven't seen any parts come out over 3mill without burning. This is dark, even a grinder would have a hard time getting through this. Me likey.
#170
Thread Starter
Elite Member
iTrader: (8)
Joined: Dec 2008
Posts: 2,910
Total Cats: 51
From: Kingston, Ontario
haven't updated this much... moved, built a few manifolds since and im back working on the shop again. I did do a lot of instagram live when building these manifolds. Was pretty fun chatting with you guys when I was melting these in.
I was sent a few photos once these were delivered...
I was sent a few photos once these were delivered...
Last edited by 18psi; 09-27-2018 at 12:39 PM.
Thread
Thread Starter
Forum
Replies
Last Post
projectrally
Media
0
08-25-2015 06:48 AM