Ryan's build thread - Clean and Mean
#643
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 21,069
Total Cats: 3,133
What is odd is that the car was running pretty well until he upgraded the firmware and then it wouldn't idle and just generally behaved strangely. Ryan said that new settings became more options and that old settings changed values .
#644
Elite Member
Thread Starter
iTrader: (8)
Join Date: Jan 2012
Location: Tampa, Florida
Posts: 2,568
Total Cats: 217
For information purposes in case anyone else goes through the same thing:
Reverant built the frequency multiplier into all of his ms2extra ecu's so they use a multiple of 30.5hz. that is why my setting was at 31hz. I think the multiplier was part of the firmware though so the frequency needs to be adjusted to a normal frequency when the firmware is updated to the latest standard version.
Reverant built the frequency multiplier into all of his ms2extra ecu's so they use a multiple of 30.5hz. that is why my setting was at 31hz. I think the multiplier was part of the firmware though so the frequency needs to be adjusted to a normal frequency when the firmware is updated to the latest standard version.
#648
Elite Member
Thread Starter
iTrader: (8)
Join Date: Jan 2012
Location: Tampa, Florida
Posts: 2,568
Total Cats: 217
The car has been back together and running for about 2 weeks. Vlad has been helping me tune the car. Which has been going well but not progressing as fast as I would have liked due to having to start over from scratch with my map due to the updated firmware reaking havoc on my settings. Good news is that so far there has been no oil coming out of the turbo. Hopefully that holds true once I start making some pulls.
When I was driving it around the neighborhood streets this weekend I noticed that the turbo induction noises are a lot louder now. Something is definitely different after it was rebuilt by Southeast Power Systems.
When I was driving it around the neighborhood streets this weekend I noticed that the turbo induction noises are a lot louder now. Something is definitely different after it was rebuilt by Southeast Power Systems.
#654
Elite Member
Thread Starter
iTrader: (8)
Join Date: Jan 2012
Location: Tampa, Florida
Posts: 2,568
Total Cats: 217
Car is running but I ended up losing 4 of my 9 team members at work within a 3 week period so I have been absolutely slammed. Between that mess and planning my wedding, I haven't had time to mess with the car. This weekend is supposed to include more pulls and tuning. I think I should be able to get a virtual dyno graph from it now if nothing goes wrong.
#655
Elite Member
Thread Starter
iTrader: (8)
Join Date: Jan 2012
Location: Tampa, Florida
Posts: 2,568
Total Cats: 217
I drove the car for about 5 hours total last weekend while tuning fuel and looking for signs of oil leaks from the turbo. Luckily there were no signs of oil leaks and I did get some clean pulls in that I have run through virtual dyno. These numbers are nothing spectacular but I am running just the wastegate at 14psi with a pretty conservative spark map and fueling that could still using some dialing in. I am going to be doing additional tuning over the next few weeks and will continue to post log data as I go. I am thinking of upgrading to MS3 to control VVT and better manage the alternator draw with AC. A flattop or skunk2 would also be nice to replace my shitty VTCS manifold.
#657
You're looking at the wrong line. That's VD reading "boost" which it doesn't unless you go into the settings and update it to read properly.
He's running high 11's low 12's AFR, and about 15psi (wastegate pressure, no boost controller) right now. I'm e-tuning his car and just sent next revision/map based on his logs
Timing is conservative too because we're on pump gas and I don't take big steps when tuning a car across the country
I'm pretty sure we can hit 300, but after that he's gonna need:
1) a non-crappy IM
2) much more map sensor
3) really think about ms3+
He's running high 11's low 12's AFR, and about 15psi (wastegate pressure, no boost controller) right now. I'm e-tuning his car and just sent next revision/map based on his logs
Timing is conservative too because we're on pump gas and I don't take big steps when tuning a car across the country
I'm pretty sure we can hit 300, but after that he's gonna need:
1) a non-crappy IM
2) much more map sensor
3) really think about ms3+
#659
FWIW
Since I posted in this thread about WG setup, I have moved to the two port setup below and it made a significant improvement in spool over a single signal line to the lower/opening port on the WG. I'm using an Innovate SCG-1 EBC but the principle is the same. The controller keeps boost pressure at the top port until target and that added pressure helps keep the valve shut up to that point.
https://cimg3.ibsrv.net/gimg/www.mia...06a841d8e5.png
https://cimg3.ibsrv.net/gimg/www.mia...06a841d8e5.png