More Money Than Brains
#442
Junior Member
iTrader: (1)
Join Date: Sep 2017
Location: Huntington Beach, CA
Posts: 230
Total Cats: 22
I'm running the same engine mounts. As the actuator is nearly centered over the engine mounts i doubt the angle of the motor/trans would affect it that much.
Once I get my axles from V8R I'll be installing the BMW/getrag system as well. I ordered a new hood since I folded my old one over my roof. If it offers better clearance than the stock one I'll let you know.
Once I get my axles from V8R I'll be installing the BMW/getrag system as well. I ordered a new hood since I folded my old one over my roof. If it offers better clearance than the stock one I'll let you know.
#443
I'm running the same engine mounts. As the actuator is nearly centered over the engine mounts i doubt the angle of the motor/trans would affect it that much.
Once I get my axles from V8R I'll be installing the BMW/getrag system as well. I ordered a new hood since I folded my old one over my roof. If it offers better clearance than the stock one I'll let you know.
Once I get my axles from V8R I'll be installing the BMW/getrag system as well. I ordered a new hood since I folded my old one over my roof. If it offers better clearance than the stock one I'll let you know.
#444
Junior Member
iTrader: (1)
Join Date: Sep 2017
Location: Huntington Beach, CA
Posts: 230
Total Cats: 22
Ccp fabrication. Ryan @ Singular told me about them. It's where he got his glass doors I believe.
Na hood with the naca headlight cover glassed over. So it will be a straight flat hood, no openings except for the ones I want (5 singular vents). Paul @ CCP said the bracing under the hood was 1/4" tall and there are only a couple of them. I'll send pictures when it comes. If the hood is identical, I should still have to notch my louver to get it to close. We'll see
Na hood with the naca headlight cover glassed over. So it will be a straight flat hood, no openings except for the ones I want (5 singular vents). Paul @ CCP said the bracing under the hood was 1/4" tall and there are only a couple of them. I'll send pictures when it comes. If the hood is identical, I should still have to notch my louver to get it to close. We'll see
#445
Ccp fabrication. Ryan @ Singular told me about them. It's where he got his glass doors I believe.
Na hood with the naca headlight cover glassed over. So it will be a straight flat hood, no openings except for the ones I want (5 singular vents). Paul @ CCP said the bracing under the hood was 1/4" tall and there are only a couple of them. I'll send pictures when it comes. If the hood is identical, I should still have to notch my louver to get it to close. We'll see
Na hood with the naca headlight cover glassed over. So it will be a straight flat hood, no openings except for the ones I want (5 singular vents). Paul @ CCP said the bracing under the hood was 1/4" tall and there are only a couple of them. I'll send pictures when it comes. If the hood is identical, I should still have to notch my louver to get it to close. We'll see
#447
Junior Member
iTrader: (1)
Join Date: Sep 2017
Location: Huntington Beach, CA
Posts: 230
Total Cats: 22
The innovate has 2 output wires. Brown and yellow I believe, and the setting on the calibration are different for both.
One is for the correct default in megasquirt, the other isn't. I ended up logging into the innovate gause and made both outputs the same and then input those in a custom wideband option in megasquirt. I probably made it twice as hard on myself, but it works perfect now
One is for the correct default in megasquirt, the other isn't. I ended up logging into the innovate gause and made both outputs the same and then input those in a custom wideband option in megasquirt. I probably made it twice as hard on myself, but it works perfect now
#448
The innovate has 2 output wires. Brown and yellow I believe, and the setting on the calibration are different for both.
One is for the correct default in megasquirt, the other isn't. I ended up logging into the innovate gause and made both outputs the same and then input those in a custom wideband option in megasquirt. I probably made it twice as hard on myself, but it works perfect now
One is for the correct default in megasquirt, the other isn't. I ended up logging into the innovate gause and made both outputs the same and then input those in a custom wideband option in megasquirt. I probably made it twice as hard on myself, but it works perfect now
As an aside pulled the car out of the garage for the first time in 6 months. Looks good. Taking it tomorrow for all the exhaust fabrication. Drove it quickly about 200 yards around my complex. No funny noises or anything other than an open downpipe. Only thing I noticed was neutral was sluggish. As in the car rolled slowly backwards with the car in neutral and the clutch also in. Not sure if its the new brakes or what...
Also got this piece in...will cut out the transmission tunnel and have this welded in. Found a company that makes them for SPEC miata. After its in will have the custom seat brackets made so my seats fit better in the car.
KMiata shift **** showed up too. Thing is nice and heavy. Could kill someone with it. I like it.
#449
Not sure on the specifics of the trans you are using, but there may be an issue with it if there is too much resistance while just spinning whatever the output shaft is.
Do you know for a fact the clutch is fully disengaged? It doesnt roll forwards atall, or maybe check if ms registers any load.
How is driveshaft alignment?
Brakes may be dragging, could clear up after bedding (im assuming this hasnt been done)
Diff might be set improperly
Axles new too? Could just need a high speed run or something to clear up.
Rear wheel bearings installed correctly?
Just spitballin, maybe it helps.
Do you know for a fact the clutch is fully disengaged? It doesnt roll forwards atall, or maybe check if ms registers any load.
How is driveshaft alignment?
Brakes may be dragging, could clear up after bedding (im assuming this hasnt been done)
Diff might be set improperly
Axles new too? Could just need a high speed run or something to clear up.
Rear wheel bearings installed correctly?
Just spitballin, maybe it helps.
#450
Junior Member
iTrader: (1)
Join Date: Sep 2017
Location: Huntington Beach, CA
Posts: 230
Total Cats: 22
Heads up on the Amazon coils. Show correct part numbers and all but my dwell needs to be at 4.5 otherwise I get issues. Toby who tuned my car said the dwell on the d585's should work fine at 2.5, but I was getting blowout. I also originally used eBay connectors but cylinder 3 sometimes needs a jiggle to work. Ended up buying a set of 8 coils with factory harnessss off eBay. Made a new wiring harness out of the factory GM one and hope to not have any more issues.
#451
Not sure on the specifics of the trans you are using, but there may be an issue with it if there is too much resistance while just spinning whatever the output shaft is.
Do you know for a fact the clutch is fully disengaged? It doesnt roll forwards atall, or maybe check if ms registers any load.
How is driveshaft alignment?
Brakes may be dragging, could clear up after bedding (im assuming this hasnt been done)
Diff might be set improperly
Axles new too? Could just need a high speed run or something to clear up.
Rear wheel bearings installed correctly?
Just spitballin, maybe it helps.
Do you know for a fact the clutch is fully disengaged? It doesnt roll forwards atall, or maybe check if ms registers any load.
How is driveshaft alignment?
Brakes may be dragging, could clear up after bedding (im assuming this hasnt been done)
Diff might be set improperly
Axles new too? Could just need a high speed run or something to clear up.
Rear wheel bearings installed correctly?
Just spitballin, maybe it helps.
I’m hoping just the brakes...the axles and driveshaft spin easily by hand until I mounted the tires and pads so here’s hoping.
#452
Heads up on the Amazon coils. Show correct part numbers and all but my dwell needs to be at 4.5 otherwise I get issues. Toby who tuned my car said the dwell on the d585's should work fine at 2.5, but I was getting blowout. I also originally used eBay connectors but cylinder 3 sometimes needs a jiggle to work. Ended up buying a set of 8 coils with factory harnessss off eBay. Made a new wiring harness out of the factory GM one and hope to not have any more issues.
Good to know...if I have issues I’ll just order new ones from the dealer. The harness is brand new from wiring solutions so I think it’s solid.