Pat's Ebay Turbo Compound Boost Build
#1504
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,351
Total Cats: 524
In a few years, the car will run on compressed air, and make 800whp doing it. But for now, it's going to have an air tank to spool the turbo so I can get a good launch on the car and quickly spool the turbo when needed. Been busy, but going to try and look at the car tomorrow about if it's possible to put a belt driven compressor on the motor. That would be a lot better than an electric compressor.
I've looked into the electric turbo that do make a few psi boost. All of them are too expensive for what they do. I've looked into making my own, but for now, not pursuing that, too many things to have to figure out and things that could go wrong. But if I ever went that route, my goal would be to make one large enough and powerful enough to make say, 30 PSI boost by itself. I would only do it if I could build one that could perform as well as a regular exhaust driven turbo. Anything else seems like a waste, just run a regular turbo.
I've looked into the electric turbo that do make a few psi boost. All of them are too expensive for what they do. I've looked into making my own, but for now, not pursuing that, too many things to have to figure out and things that could go wrong. But if I ever went that route, my goal would be to make one large enough and powerful enough to make say, 30 PSI boost by itself. I would only do it if I could build one that could perform as well as a regular exhaust driven turbo. Anything else seems like a waste, just run a regular turbo.
#1505
Hm. My initial inclination was that dumping it into the intake wasn't going to do anything, that it would run out in a fraction of a second. I did a bit of back-of-the-envelope math to prove it and decided I was wrong.
Let's assume a 5 gallon tank at 200 psi (this seems to be about at the upper range of what's reasonable to stick in the trunk). That's 18.5 liters at 13.6 atmospheres, or about 250 liter-atmospheres. Assume the motor is at 3000 RPM, is 1.8L, and we want 15 psi of boost to spool it, we need 45 liter-atmospheres per second to make that boost, so that's about 5 seconds of boost.
So OK, maybe it isn't completely stupid for a drag racing application. Looks like it'd need a 1 inch air line to dump those 45 liters/sec (90 CFM) though, and I hate to think how big the regulator would be..
--Ian
Let's assume a 5 gallon tank at 200 psi (this seems to be about at the upper range of what's reasonable to stick in the trunk). That's 18.5 liters at 13.6 atmospheres, or about 250 liter-atmospheres. Assume the motor is at 3000 RPM, is 1.8L, and we want 15 psi of boost to spool it, we need 45 liter-atmospheres per second to make that boost, so that's about 5 seconds of boost.
So OK, maybe it isn't completely stupid for a drag racing application. Looks like it'd need a 1 inch air line to dump those 45 liters/sec (90 CFM) though, and I hate to think how big the regulator would be..
--Ian
#1506
These guys are about to start production sales on boost in a can last I saw. They go through 1.5 of those bottles in one 1/4 mi pass.
Compressed Air supercharging (CAS) ? Dramatic Power Gains And Outstanding Reliability
Article doing a quicker rundown:
A New Kind of Compressed Air Powers This 9-Second Camaro ? and Changes Everything
Long (27m) but interesting and in-depth interview
Sorry to drive further off topic, but I stumbled upon the vid recently. Did you post a log of your launch? I might have missed it if you did, but would love to see the MAP signal just for fun.
#1507
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,351
Total Cats: 524
Your HP number seems to spot on for you to not be referencing this, but if you weren't or others didn't know
These guys are about to start production sales on boost in a can last I saw. They go through 1.5 of those bottles in one 1/4 mi pass.
Compressed Air supercharging (CAS) ? Dramatic Power Gains And Outstanding Reliability
Article doing a quicker rundown:
A New Kind of Compressed Air Powers This 9-Second Camaro ? and Changes Everything
Long (27m) but interesting and in-depth interview
Sorry to drive further off topic, but I stumbled upon the vid recently. Did you post a log of your launch? I might have missed it if you did, but would love to see the MAP signal just for fun.
These guys are about to start production sales on boost in a can last I saw. They go through 1.5 of those bottles in one 1/4 mi pass.
Compressed Air supercharging (CAS) ? Dramatic Power Gains And Outstanding Reliability
Article doing a quicker rundown:
A New Kind of Compressed Air Powers This 9-Second Camaro ? and Changes Everything
Long (27m) but interesting and in-depth interview
Sorry to drive further off topic, but I stumbled upon the vid recently. Did you post a log of your launch? I might have missed it if you did, but would love to see the MAP signal just for fun.
Ok, I was! I absolutely wanna try either their setup, or my version of that in the future. For drag racing, that is perfect. It's basically a nitrous motor that doesn't use nitrous.
I haven't posted a log lately I don't think. I haven't launched the car with the EFR yet, hope to do that tomorrow, and if I do, I'll post that log hopefully with a time slip!
#1511
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,351
Total Cats: 524
This is the video I was given, check out how well this works! I am optimistic I can get similar results with a similar setup on my car.
#1515
Elite Member
iTrader: (2)
Join Date: Aug 2016
Location: New Fucking Jersey
Posts: 3,890
Total Cats: 143
Yes it will, but for spoolup that's ok for me. I'll just tune the AFRs without the air system on.
This is the video I was given, check out how well this works! I am optimistic I can get similar results with a similar setup on my car.
https://www.youtube.com/watch?v=Ulkjqn7_huA
This is the video I was given, check out how well this works! I am optimistic I can get similar results with a similar setup on my car.
https://www.youtube.com/watch?v=Ulkjqn7_huA
Seriously though, that's incredible.
#1516
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,351
Total Cats: 524
Small update, I've had a running list of "little things" I needed to get around to fixing or adjusting. All crap like tightening clamps, fixing an exhaust leak at a V-band, fixing a few rattles, and opening the spool valve permanently to see how that affects the spool on the front turbo. Actually it was 17 different items and took all day to do them, and I probably added 3 or 4 more things I found while doing those. It's late, and raining, so no test drive, will do that when it's dry and see how it does. A quick startup and rev seems to indicate no rattles, so hopes that those are history now. Exhaust is louder with the spool valve out, so that is kinda cool. It will be interesting to see how the EFR responds to that change, when I had the ebay turbo the valve helped overall, but I wanted to see how it did with the EFR.
I recently went to iridium plugs to see if that would fix my misfire. I put them in as they were removed from the box at .029". Well, they misfired probably worse than the coppers @ .015", although it was more like an on/off switch with the iridium's. So I gapped those down to .018" and have my fingers crossed that will finally fix my misfire.
Don't worry, the air setup will happen. Not sure exactly when, it's not a huge rush but it will go on the car.
I recently went to iridium plugs to see if that would fix my misfire. I put them in as they were removed from the box at .029". Well, they misfired probably worse than the coppers @ .015", although it was more like an on/off switch with the iridium's. So I gapped those down to .018" and have my fingers crossed that will finally fix my misfire.
Don't worry, the air setup will happen. Not sure exactly when, it's not a huge rush but it will go on the car.
#1519
Elite Member
Thread Starter
iTrader: (16)
Join Date: Aug 2007
Location: Houston, TX
Posts: 9,351
Total Cats: 524
Small update, I've had a running list of "little things" I needed to get around to fixing or adjusting. All crap like tightening clamps, fixing an exhaust leak at a V-band, fixing a few rattles, and opening the spool valve permanently to see how that affects the spool on the front turbo. Actually it was 17 different items and took all day to do them, and I probably added 3 or 4 more things I found while doing those. It's late, and raining, so no test drive, will do that when it's dry and see how it does. A quick startup and rev seems to indicate no rattles, so hopes that those are history now. Exhaust is louder with the spool valve out, so that is kinda cool. It will be interesting to see how the EFR responds to that change, when I had the ebay turbo the valve helped overall, but I wanted to see how it did with the EFR.
I recently went to iridium plugs to see if that would fix my misfire. I put them in as they were removed from the box at .029". Well, they misfired probably worse than the coppers @ .015", although it was more like an on/off switch with the iridium's. So I gapped those down to .018" and have my fingers crossed that will finally fix my misfire.
Don't worry, the air setup will happen. Not sure exactly when, it's not a huge rush but it will go on the car.
I recently went to iridium plugs to see if that would fix my misfire. I put them in as they were removed from the box at .029". Well, they misfired probably worse than the coppers @ .015", although it was more like an on/off switch with the iridium's. So I gapped those down to .018" and have my fingers crossed that will finally fix my misfire.
Don't worry, the air setup will happen. Not sure exactly when, it's not a huge rush but it will go on the car.
So.... I've driven the car a few times since running the new iridium plugs at .018" gap and... IT FIXED THE MISFIRE!!!!!!!!!!!! Thank God.
I haven't had a laptop in the car in a while. Decided to pull the logs and have a look. Well....
I'm apparently running 35 PSI, and at 7,000 RPMs the ID 1300 injectors that flow 1700cc/min at my fuel pressure, are at 97.3% duty cycle with AFR's of 10.8. That explains why it fells, uh, pretty fast. LOL maxed out ID1300s! I made a pull to 7500 and it leaned out but was ripping!
Did I mention it's retarded quick? I need more injector, lot more. I wanna run 45 PSI and see what that's like. I'm guessing it's back to 500whp or so right now based on the duty cycle, but now doing that with 1,500 RPM less, and 3 lbs less boost vs two years ago.