Drag racing setup
#1
Drag racing setup
So, with the challenge car, im hoping for deep into the 12s or high 11s based on power to weight.
however, i know NOTHING about making an independent rear hook up on the strip. Always been a stick axle and leaf springs guy.
what is the proper setup to make a miata hook for sub 1.8 60 foot times? Other than wrinkle walls and skinnys up front.
however, i know NOTHING about making an independent rear hook up on the strip. Always been a stick axle and leaf springs guy.
what is the proper setup to make a miata hook for sub 1.8 60 foot times? Other than wrinkle walls and skinnys up front.
#2
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 21,065
Total Cats: 3,131
Paging @miata2fast Troy. From what I recall, keep the cv shaft straight between the diff and wheel hubs, add spring in the rear to keep it from squatting when it transfers.
Don't use too tall a slick. Diameter is important.
Don't use too tall a slick. Diameter is important.
#3
So, with the challenge car, im hoping for deep into the 12s or high 11s based on power to weight.
however, i know NOTHING about making an independent rear hook up on the strip. Always been a stick axle and leaf springs guy.
what is the proper setup to make a miata hook for sub 1.8 60 foot times? Other than wrinkle walls and skinnys up front.
however, i know NOTHING about making an independent rear hook up on the strip. Always been a stick axle and leaf springs guy.
what is the proper setup to make a miata hook for sub 1.8 60 foot times? Other than wrinkle walls and skinnys up front.
#4
slicks, slicks are the only way you are going to run those 60's and not leave your drivetrain at the light. I have been to the track a few times with my Miata's and have always had **** wheel hop. I ran 24.5x9x13 slicks last time and it was a game changer. 1.8 60's and zero wheel hop, butter smooth 2nd gear burn outs. Those slicks were to big, 23x8x13 M&H's are the way to go.
#6
Did you run an 1.800' 60 ft? Or a 1.89? How consistently could you run that time?
There is a big difference between doing a good 60' once, vs every single time you line up. Some yesterday bragged about running a 1.7 60', but they didn't post time slips, or what the actual time was, or how consistently his car ran that time he didn't post.
There is a big difference between doing a good 60' once, vs every single time you line up. Some yesterday bragged about running a 1.7 60', but they didn't post time slips, or what the actual time was, or how consistently his car ran that time he didn't post.
#7
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 21,065
Total Cats: 3,131
This wasn't Troy's best 60' but was his best ET of the night back in 2010. Naturally aspirated Miata with wrinkle wall slicks, IDK what size but I think they were 22 or 23 inches by 7 wide. He was launching at 5000+RPM if I recall correctly.
#8
My car is setup for drifting and has **** Stance AL+ coils from 2008. I ran consistent 1.8's all day with tires way to big, and my alternator failed half after that 12.4 run and I was running 9.5 volts with out knowing for the rest of the day. If I went back with 23" slicks now I think I could run high 1.6's and get 11.9's .
To me the slicks are more about getting that smooth launch, having zero wheel hop is what its all about. I couldn't even do a burn out to warm and clean the tires on street radials.
#9
So, how stiff are we talking about here?
how do you control the wheelhop?
rest makes sense.
since i will be boosted v6, gearing and tire size will probably need to be different, but we wont know that until the first test day.
and 1.8x 60 foot times are my goal. If i can get 1.5x, we should rrally be cooking. But sub 2.00 is my realistically expected results. With this being the challenge and all, we may not have the budget for perfect. But if i can learn what the optimal is, i can shoot for it.
how do you control the wheelhop?
rest makes sense.
since i will be boosted v6, gearing and tire size will probably need to be different, but we wont know that until the first test day.
and 1.8x 60 foot times are my goal. If i can get 1.5x, we should rrally be cooking. But sub 2.00 is my realistically expected results. With this being the challenge and all, we may not have the budget for perfect. But if i can learn what the optimal is, i can shoot for it.
#10
So, how stiff are we talking about here?
how do you control the wheelhop?
rest makes sense.
since i will be boosted v6, gearing and tire size will probably need to be different, but we wont know that until the first test day.
and 1.8x 60 foot times are my goal. If i can get 1.5x, we should rrally be cooking. But sub 2.00 is my realistically expected results. With this being the challenge and all, we may not have the budget for perfect. But if i can learn what the optimal is, i can shoot for it.
how do you control the wheelhop?
rest makes sense.
since i will be boosted v6, gearing and tire size will probably need to be different, but we wont know that until the first test day.
and 1.8x 60 foot times are my goal. If i can get 1.5x, we should rrally be cooking. But sub 2.00 is my realistically expected results. With this being the challenge and all, we may not have the budget for perfect. But if i can learn what the optimal is, i can shoot for it.
#11
Bushings and **** only helps to a point, now the last time I went to the track on street tires I had 205 Dunlop dz102. I have yet today run it down the track on my 245 VR-1’s .
but I have V8R control arms with all Polly bushings, Delrin sub frame bushings and I tied my 6pt oem sub frame brace into the diff/ppf mounting point.
I remove the front sway and set the front suspension to max soft. You want the front to lift and transfer weight to the rear.
But it so far nothing has calmed the wheel hop except drag slicks. I used to go around the water box and launch the car at like 3500-4000 and ***** foot it out of the hole. Only could get high 2.1 60’s
but I have V8R control arms with all Polly bushings, Delrin sub frame bushings and I tied my 6pt oem sub frame brace into the diff/ppf mounting point.
I remove the front sway and set the front suspension to max soft. You want the front to lift and transfer weight to the rear.
But it so far nothing has calmed the wheel hop except drag slicks. I used to go around the water box and launch the car at like 3500-4000 and ***** foot it out of the hole. Only could get high 2.1 60’s
#12
Moderator
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 21,065
Total Cats: 3,131
Wrinkle wall slicks will prevent hop and absorb power pulses like a rubber band and release them smoothly. Practice higher and higher rpm launches until you reach the point where it doesn't bog at launch. That's what I remember. Slicks will still spin a little, but it is needed to avoid bogging to do it right.
#13
Wrinkle wall slicks will prevent hop and absorb power pulses like a rubber band and release them smoothly. Practice higher and higher rpm launches until you reach the point where it doesn't bog at launch. That's what I remember. Slicks will still spin a little, but it is needed to avoid bogging to do it right.
exactly, I was launching at 8k
#14
Did you run an 1.800' 60 ft? Or a 1.89? How consistently could you run that time?
There is a big difference between doing a good 60' once, vs every single time you line up. Some yesterday bragged about running a 1.7 60', but they didn't post time slips, or what the actual time was, or how consistently his car ran that time he didn't post.
There is a big difference between doing a good 60' once, vs every single time you line up. Some yesterday bragged about running a 1.7 60', but they didn't post time slips, or what the actual time was, or how consistently his car ran that time he didn't post.
#15
Retired Mech Design Engr
iTrader: (3)
Join Date: Jan 2013
Location: Seneca, SC
Posts: 5,012
Total Cats: 859
Wrinkle wall slicks will prevent hop and absorb power pulses like a rubber band and release them smoothly. Practice higher and higher rpm launches until you reach the point where it doesn't bog at launch. That's what I remember. Slicks will still spin a little, but it is needed to avoid bogging to do it right.
Any recommendations for that?