sonofthehill sets his sights on MK ULTRA
#826
Thread Starter
Elite Member
iTrader: (1)
Joined: Apr 2014
Posts: 3,108
Total Cats: 560
From: SF Bay Area, CA
Well, I sent Pat my tune and log. I guess it's time to come clean, I have been working on my timing table for a 5 gallon blend of AV100LL that I was hoping to run last Wednesday. That is why I have been increasing my timing so much.
Pat, maybe you can help me figure out why my idle valve opens when it's not supposed to, as far as I can tell.
The only possibilities for a boost leak left that I can think of are my intake manifold and the compressor housing.
Pat, maybe you can help me figure out why my idle valve opens when it's not supposed to, as far as I can tell.
The only possibilities for a boost leak left that I can think of are my intake manifold and the compressor housing.
#827
Thread Starter
Elite Member
iTrader: (1)
Joined: Apr 2014
Posts: 3,108
Total Cats: 560
From: SF Bay Area, CA
So I changed my wastegate can to another one I modded since I can't find any boost leaks. A little better, my old seal was melted but it still sealed. I ordered one I can swap springs in so we'll see how that goes. This is a 3rd gear spool, can't spool 4th without the track, no race this week. I am adjusting the timing, haven't seen boost that low before, also I upped my MAP smoothing from 20% to 40% although Pat wants me to set it to 100%. Not yet man, let me get the other can.
#830
Thread Starter
Elite Member
iTrader: (1)
Joined: Apr 2014
Posts: 3,108
Total Cats: 560
From: SF Bay Area, CA
Is this what I need to make the 255l pump and Fuelab regulator work right? Will I have any problems running my injectors at 70 or 80 psi?
Can't seem to find a picture of the other side anymore but it has the o ring a few millimeters from the end.
Can't seem to find a picture of the other side anymore but it has the o ring a few millimeters from the end.
#834
SADFab Destructive Testing Engineer
iTrader: (5)
Joined: Apr 2014
Posts: 18,642
Total Cats: 1,866
From: Beaverton, USA
Run manifold referenced if you can. It involves more work but will work better.
if you run 80psi base, then you are trying to idle with 80psi of fuel pressure. And at 20psi of boost you only have an effective 60psi of pressure.
if you run 80psi base, then you are trying to idle with 80psi of fuel pressure. And at 20psi of boost you only have an effective 60psi of pressure.
#838
Thread Starter
Elite Member
iTrader: (1)
Joined: Apr 2014
Posts: 3,108
Total Cats: 560
From: SF Bay Area, CA
My ms2 doesn't suck, it blows!
Doesn't sound too difficult to run a boost reference. I have an "inspection opportunity" not too far away, so this will likely wait until then. For the moment I am stuck around 240 or 250 kpa.
Doesn't sound too difficult to run a boost reference. I have an "inspection opportunity" not too far away, so this will likely wait until then. For the moment I am stuck around 240 or 250 kpa.
#840
Thread Starter
Elite Member
iTrader: (1)
Joined: Apr 2014
Posts: 3,108
Total Cats: 560
From: SF Bay Area, CA
Yeah, my car is basically a freaking hairdresser beach mobile. Can barely get out of the teens and doesn't even make 3 times factory power. I am over it, I want a big **** fuel upgrade and a huge honkin' t3 to compliment my upgrade.
I have to say, those coils are lighting shyat up no matter what tho, misfires gone.
I have to say, those coils are lighting shyat up no matter what tho, misfires gone.