Turbo Smurfette - Build in progress (slow)
#1123
mkturbo.com
iTrader: (24)
Join Date: May 2006
Location: Charleston SC
Posts: 15,194
Total Cats: 1,687
This is exactly how I think. I have yet to spend a penny in head work on any of my builds. I just don't see the amount of money spent bringing any real gain. I throw in new valve seals and make sure its flat, then it goes on the car. I rather turn up ht psi a few pounds and make whatever additional power the head work would do.
#1124
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
Cranking up boost is great until those few psi push back and say nope nope nope.
It's been rainy out. Can't do my final pull. I'll have to put Smurfette down for the season if I'm talking end tank rewelding. Some local places don't seem interested in the work so I may just send it out to Bell Intercooler to chop and weld.
I wonder if we're comparing against Soviet's build and his monster timing table, I'd probably have to jump on Mach V's (or maybe Moore Automotive's) DynoJet for glory numbers. Otherwise I'd be fun to pit PTuning vs VladTuning numbers on the DynoDynamics
It's been rainy out. Can't do my final pull. I'll have to put Smurfette down for the season if I'm talking end tank rewelding. Some local places don't seem interested in the work so I may just send it out to Bell Intercooler to chop and weld.
I wonder if we're comparing against Soviet's build and his monster timing table, I'd probably have to jump on Mach V's (or maybe Moore Automotive's) DynoJet for glory numbers. Otherwise I'd be fun to pit PTuning vs VladTuning numbers on the DynoDynamics
#1131
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
4th gear only for clean pulls without tire spin. It's getting a little intense.
Oof, good thing I have a spare trans, a built head on the way and I can always ask @Shibby for a loaner block.
Oh yea! This'll likely be a winter project.
That taper though! It stabilizes to 27-28ish.
Vlad also noted timing is still relatively conservative. Yikes.
That taper though! It stabilizes to 27-28ish.
Vlad also noted timing is still relatively conservative. Yikes.
#1133
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
Aktualisirung:
- DynoJet has been booked at Moore Automotive for October 27th. This will allow a week of my return to iron out any action items Vlad deems necessary. I would like to get back on PTuning's Dyno Dynamics, to better understand the changes from fixing the boost leak and having Vlad smooth over things; this will have to be another day.
- For science, I'll send the intercooler back to Bell for inlet/outlet modification when the car is down for the winter season. When touching back on this in spring, we'll see if a simple pipe diameter change will help open up top. For now it seems 2" is fine for most goals, I kinda just want to push it
- For science, if it turns out it's the head, I've been sitting on a built head from HeadGames Motorworks (semi-local) which include full PnP, SUB conversion, +1 O/S valves and heavy valve train. Still stock cams as I hadn't built the block considering larger lift or fly cutting the piston relief's for +2. I'm uncertain if I'll just sit on this until the next BP iteration with a possible higher compression build (currently 8.6:1) using a different turbo TBD or if Smurfette will be jumping ship to join the Honda/GM camp during resurrection.
- DynoJet has been booked at Moore Automotive for October 27th. This will allow a week of my return to iron out any action items Vlad deems necessary. I would like to get back on PTuning's Dyno Dynamics, to better understand the changes from fixing the boost leak and having Vlad smooth over things; this will have to be another day.
- For science, I'll send the intercooler back to Bell for inlet/outlet modification when the car is down for the winter season. When touching back on this in spring, we'll see if a simple pipe diameter change will help open up top. For now it seems 2" is fine for most goals, I kinda just want to push it
- For science, if it turns out it's the head, I've been sitting on a built head from HeadGames Motorworks (semi-local) which include full PnP, SUB conversion, +1 O/S valves and heavy valve train. Still stock cams as I hadn't built the block considering larger lift or fly cutting the piston relief's for +2. I'm uncertain if I'll just sit on this until the next BP iteration with a possible higher compression build (currently 8.6:1) using a different turbo TBD or if Smurfette will be jumping ship to join the Honda/GM camp during resurrection.
#1134
Aktualisirung:
- DynoJet has been booked at Moore Automotive for October 27th. This will allow a week of my return to iron out any action items Vlad deems necessary. I would like to get back on PTuning's Dyno Dynamics, to better understand the changes from fixing the boost leak and having Vlad smooth over things; this will have to be another day.
- For science, I'll send the intercooler back to Bell for inlet/outlet modification when the car is down for the winter season. When touching back on this in spring, we'll see if a simple pipe diameter change will help open up top. For now it seems 2" is fine for most goals, I kinda just want to push it
- For science, if it turns out it's the head, I've been sitting on a built head from HeadGames Motorworks (semi-local) which include full PnP, SUB conversion, +1 O/S valves and heavy valve train. Still stock cams as I hadn't built the block considering larger lift or fly cutting the piston relief's for +2. I'm uncertain if I'll just sit on this until the next BP iteration with a possible higher compression build (currently 8.6:1) using a different turbo TBD or if Smurfette will be jumping ship to join the Honda/GM camp during resurrection.
- DynoJet has been booked at Moore Automotive for October 27th. This will allow a week of my return to iron out any action items Vlad deems necessary. I would like to get back on PTuning's Dyno Dynamics, to better understand the changes from fixing the boost leak and having Vlad smooth over things; this will have to be another day.
- For science, I'll send the intercooler back to Bell for inlet/outlet modification when the car is down for the winter season. When touching back on this in spring, we'll see if a simple pipe diameter change will help open up top. For now it seems 2" is fine for most goals, I kinda just want to push it
- For science, if it turns out it's the head, I've been sitting on a built head from HeadGames Motorworks (semi-local) which include full PnP, SUB conversion, +1 O/S valves and heavy valve train. Still stock cams as I hadn't built the block considering larger lift or fly cutting the piston relief's for +2. I'm uncertain if I'll just sit on this until the next BP iteration with a possible higher compression build (currently 8.6:1) using a different turbo TBD or if Smurfette will be jumping ship to join the Honda/GM camp during resurrection.
#1135
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
Yea... Back when a bunch of this started, a lot of the easy button kits weren't fully developed or I also didn't (and still do not) have facility for accommodating more complex swaps. This was, after all my daily driver in all its forms for the better part of 5 years.
Now with a second car, and the prospect of downtime not affecting my work health, a hot swap is now feasible. I just did my best the easiest way I could with what was available at the time. My first motor was built in a storage unit lol.
Now with a second car, and the prospect of downtime not affecting my work health, a hot swap is now feasible. I just did my best the easiest way I could with what was available at the time. My first motor was built in a storage unit lol.
#1137
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
FM2 clutch is slipping on the dyno. Time to start thinking about twin disk or kmiata BMW trans which would mean that brand new v8r PPF will go unused.
Or maybe just start building the next iteration and let this setup run its course.
Or maybe just start building the next iteration and let this setup run its course.
Last edited by psyber_0ptix; 10-27-2017 at 11:12 AM.