Turbo Oil Drain Location Drilled Out of Car
#1
Turbo Oil Drain Location Drilled Out of Car
I have searched and read many threads on how to drill and tap a return hole in the oil pan for a turbo oil drain line while the engine is in the car. I am building an engine, so it is outside of the car. Therefore, I have a much easier time drilling the hole if there is a better location. I also am thinking about welding in a 3/8 NPT female bung rather than drilling and tapping the pan itself. This is in preparation for the TSE EFR turbo kit.
Has anyone welded in a 3/8 NPT bung before? I've seen several AN fittings welded in but can't find an example of a NPT bung. Is that because it is a bad idea?
If I put the hole further back on the oil pan instead of below the AC bracket, will there be a problem with clearing lines or anything in the car? Is there a better location than the standard under the AC bracket?
I am swapping a build VVT engine into a 1991 chassis.
Has anyone welded in a 3/8 NPT bung before? I've seen several AN fittings welded in but can't find an example of a NPT bung. Is that because it is a bad idea?
If I put the hole further back on the oil pan instead of below the AC bracket, will there be a problem with clearing lines or anything in the car? Is there a better location than the standard under the AC bracket?
I am swapping a build VVT engine into a 1991 chassis.
#2
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,028
Total Cats: 304
This is exactly what you need, you need an aluminum one because your pan is aluminum.
As a matter of fact, the one in the photo I can sell you because I don't have a need for it. PM me your address and I will ship it to you for like five bucks. I think it's a -12, it has a 1/2" diameter ID.
#3
I have searched and read many threads on how to drill and tap a return hole in the oil pan for a turbo oil drain line while the engine is in the car. I am building an engine, so it is outside of the car. Therefore, I have a much easier time drilling the hole if there is a better location. I also am thinking about welding in a 3/8 NPT female bung rather than drilling and tapping the pan itself. This is in preparation for the TSE EFR turbo kit.
Has anyone welded in a 3/8 NPT bung before? I've seen several AN fittings welded in but can't find an example of a NPT bung. Is that because it is a bad idea?
If I put the hole further back on the oil pan instead of below the AC bracket, will there be a problem with clearing lines or anything in the car? Is there a better location than the standard under the AC bracket?
I am swapping a build VVT engine into a 1991 chassis.
Has anyone welded in a 3/8 NPT bung before? I've seen several AN fittings welded in but can't find an example of a NPT bung. Is that because it is a bad idea?
If I put the hole further back on the oil pan instead of below the AC bracket, will there be a problem with clearing lines or anything in the car? Is there a better location than the standard under the AC bracket?
I am swapping a build VVT engine into a 1991 chassis.
Generally, the preferred setup if you have the access is to put a NPT weld bung in the pan over drill/tap only.
#10
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,104
#11
Thanks for the info. There are many, many threads on how to add a drain hole to the pan with the engine in the car. I read through the TSE instructions, they also show how to put a drain in the pan with it on the car. I was wondering if there is a better location if one is not constrained to doing it with the engine in the car. I was thinking of something like what Codrus has, but I don't know if further back makes it difficult to get a wrench on the fitting, or if tubes are in the way, or whatever. Rearward of the AC bracket I can move the hole higher on the pan, although I don't know if there is a benefit to that or not.
#12
Former Vendor
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,104
If you want to drill further back, you may run into some as-yet-unforeseen interference issues between the oil drain and the lower radiator hose. The drain hose as-delivered will also certainly be too long for any position further back on the pan, so you'll have to build your own (our lines are crimp-fittings, not reusable). IMO there's no real-world benefit either, so it's a lot of extra work for no discernible benefit. I drill in the standard place even with the pan off the motor.