91 BRG 1.8BP MK turbo build
#161
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
I did not. I used the OE NA8 pump that came on the 94 block. I've read a number of threads where people use them in conjunction with a VVT head. Oil pressure is apparently visibly lower when VVT is engaged, but seems to be at least street reliable. I can't personally advocate it, cuz I have exactly 0 miles on this config.
#166
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
#170
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
Yep. PNP pro. I think that the TS input is ok because I'm getting a signal from the cam and crank in the high speed composite logger. I'm not confident that I wired the cam or crank sensors correctly. Is there a way to discern that from the composite log? Is it possible to wire it wrong such that you get a signal but it's... inverted or something?
#173
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
That was it! We have combustion. It was an ugly first start, but it runs.
Cooling fan kicked on maybe during, but definitely after the engine died even though coolant temp was 60*. Something funky there. Need to get on the IAC & timing. I got my weekend cut out!
Thanks everyone for the support.
Cooling fan kicked on maybe during, but definitely after the engine died even though coolant temp was 60*. Something funky there. Need to get on the IAC & timing. I got my weekend cut out!
Thanks everyone for the support.
#175
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
OK, no tach signal on the dash gauge. I spliced blue/yel to black/white at the OE igniter per the instructions in the VVT swap sticky, so I expected to get dash signal. This is what DIY has to say about tach out on the pnppro in the manual:
"J5: Tach Out on Connector J3, Pin 4I (1995.5+ Miata Only)
When this jumper is installed, the signal TACHOUT will be transmitted on pin 4I on the main ECU connector (J3). This should only be used on 95.5 1.8L Miatas."
I didn't install this jumper. Should I? Does this circuit want a pullup resistor?
*EDIT* what DIY labels as pin 4I on the ECU is pin 2I on the OE ECU, which is the black/white sig out to the igniter. Guess that answers that question.
"J5: Tach Out on Connector J3, Pin 4I (1995.5+ Miata Only)
When this jumper is installed, the signal TACHOUT will be transmitted on pin 4I on the main ECU connector (J3). This should only be used on 95.5 1.8L Miatas."
I didn't install this jumper. Should I? Does this circuit want a pullup resistor?
*EDIT* what DIY labels as pin 4I on the ECU is pin 2I on the OE ECU, which is the black/white sig out to the igniter. Guess that answers that question.
Last edited by wackbards; 05-06-2017 at 01:04 PM.
#176
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
The fan control was set to kick on if AC is on. There's no AC, and gawd knows what wiring is left from it. The ECU must think AC is on. I've turned the fan AC assist and the AC idle up function off, and we'll see what that does.
#177
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
Because I adapted a crank sensor to a '94 oil pump that wasn't designed for a crank sensor, I had to use trigger wizard to correct my base timing. It was retarded by 5.5*. Things are getting better. Baby steps! Baby steps...
#179
Senior Member
Thread Starter
iTrader: (2)
Join Date: Nov 2015
Location: Seattle
Posts: 1,426
Total Cats: 266
Well, it's running right. I had a bunch of stuff I had to fix today. First, I had the fuel lines backwards. Then I had the AC fan settings all jacked up. Then I had forgot the tach out jumper. Then I had forgot the fpr vacuum line. Then I had a problem with cyl 4 injector not firing. I ended up having to toggle the sequential settings in TS.
Also, I think the pinout documentation DIY has in the 9093 pnppro manual for sequential injection might be backwards. That was a fun game.
Also, I think the pinout documentation DIY has in the 9093 pnppro manual for sequential injection might be backwards. That was a fun game.