Launch Control
#21
Fuel table was tuned up to 220kpa
Think about it. If your cutting 4 of 5 sparks that's basically 80% cut or on a wasted spark 40% if excess un burnt fuel in the exhaust manifold finds it's way into another chamber it will stop spark ignition further cutting ignition with more Unburnt fuel. Eventually your gunna flood and lockup. And this during flat shift high rpm / inertia changes risks engine damage
Think about it. If your cutting 4 of 5 sparks that's basically 80% cut or on a wasted spark 40% if excess un burnt fuel in the exhaust manifold finds it's way into another chamber it will stop spark ignition further cutting ignition with more Unburnt fuel. Eventually your gunna flood and lockup. And this during flat shift high rpm / inertia changes risks engine damage
#22
as far as DIYautotune folks see, nothings wrong with MS and everything is wired correctly.
I'm curious to know if anyone has used LC on a 1.6 before or not.
#31
Senior Member
Thread Starter
iTrader: (2)
Join Date: Jun 2012
Location: Texas
Posts: 1,153
Total Cats: 50
Your settings look ok overall. Do us all a favor though and never post a tune as CurrentTune give it a unique name. We all have files on our computer labeled CurrentTune and it makes people not want to download your file and help you out. Another thing you may want to check is your clutch switch. The one that is located at the top of the clutch. It may not be working at all. You could replace it on I'd imagine jump the plug with a wire to see if it activates LC.
#32
Sorry about that. I can reload it with a different name.
On my car i have two switches. the first one has a brown/white wire and looks like it controls the cruise control and then one at the other end when the clutch is too the floor which im assuming is the starter interlock switch.
I also dont have a TPS since its a 1.6. I unplugged the top switch that went to the brown/white and jumped it and i still was unable to activate launch control. here is my msq/log file.
UPDATE!!!!:
If you have a 1.6 and are NOT using a vTPS you can set the calibrations for open/close to be 90 for close and 0 for open. You will get an error message about the values but accept them anyways. you will notice that your TPS always reads 100% but the MSPNP2 doesnt/cant read the values anyways. No additional sensors to unplug unless you dont want LC on while in neutral.
On my car i have two switches. the first one has a brown/white wire and looks like it controls the cruise control and then one at the other end when the clutch is too the floor which im assuming is the starter interlock switch.
I also dont have a TPS since its a 1.6. I unplugged the top switch that went to the brown/white and jumped it and i still was unable to activate launch control. here is my msq/log file.
UPDATE!!!!:
If you have a 1.6 and are NOT using a vTPS you can set the calibrations for open/close to be 90 for close and 0 for open. You will get an error message about the values but accept them anyways. you will notice that your TPS always reads 100% but the MSPNP2 doesnt/cant read the values anyways. No additional sensors to unplug unless you dont want LC on while in neutral.
Last edited by zero415; 03-28-2014 at 03:26 PM. Reason: Fix for non VTPS 1.6 people
#37
Retired Mech Design Engr
iTrader: (3)
Join Date: Jan 2013
Location: Seneca, SC
Posts: 5,012
Total Cats: 859
He had some trouble with spin on first and ran mid-9's. Then ran a 8.78 and an 8.79. Won the true street class.
Had me verifying that my MS can run launch control with only tuning involved, and looking into:
205-50R15 should work on my stock rims and present power. Shouldn't break anything if launched correctly.
Had me verifying that my MS can run launch control with only tuning involved, and looking into:
205-50R15 should work on my stock rims and present power. Shouldn't break anything if launched correctly.
#40
Retired Mech Design Engr
iTrader: (3)
Join Date: Jan 2013
Location: Seneca, SC
Posts: 5,012
Total Cats: 859
Well, now that I've managed to resurrect this thread, I have a difficulty that could use some input.
I have used F/S for some time now. I changed the LC Speed and TPS to try it this afternoon, and NOTHING.
Some pics, logs, etc. ECU is a MS3-Basic, V2, running 1.4.1 FW. It definitely sees the clutch switch as FFS is working correctly.
Settings:
Gave me this result (VSS1 = 0): Jumped right up to normal Rev Limit.
I also attached the full msg and log: calling @patsmx5 because pretty sure you use LC.
Note, I also read yours and Son's threads, and it looks like the M&H 7.5 x 23 x 15 might be a better choice of tire for my power level.
I have used F/S for some time now. I changed the LC Speed and TPS to try it this afternoon, and NOTHING.
Some pics, logs, etc. ECU is a MS3-Basic, V2, running 1.4.1 FW. It definitely sees the clutch switch as FFS is working correctly.
Settings:
Gave me this result (VSS1 = 0): Jumped right up to normal Rev Limit.
I also attached the full msg and log: calling @patsmx5 because pretty sure you use LC.
Note, I also read yours and Son's threads, and it looks like the M&H 7.5 x 23 x 15 might be a better choice of tire for my power level.