95m goes kinda fast for kinda cheap
#227
So I tore into the motor today, remove the pan, water pump, timing belt, oil pump, and water neck.
Everything came out smoothly until I hit the crank assembly. PO took out the 4 or 6? (looked like there were 2 small bolt holes besides the main 4 for the harmonic damper which were not included) The main bolt required some heat, but then the timing cog sucked to get out, I broke pretty much all the outer material out, so it looks like a need a new one of those. I could not for the life of me get the damn thing to come out, I barred the crank where the main seal goes twice, although I think I can take some sand paper and get away with it, I also hit the front of the oil pump housing pretty bad, does this even matter because nothing contacts it?
Maybe this was the cause of the low oil pressure issue? No idea where the other piece of gasket went....
Gear wear
Everything came out smoothly until I hit the crank assembly. PO took out the 4 or 6? (looked like there were 2 small bolt holes besides the main 4 for the harmonic damper which were not included) The main bolt required some heat, but then the timing cog sucked to get out, I broke pretty much all the outer material out, so it looks like a need a new one of those. I could not for the life of me get the damn thing to come out, I barred the crank where the main seal goes twice, although I think I can take some sand paper and get away with it, I also hit the front of the oil pump housing pretty bad, does this even matter because nothing contacts it?
Maybe this was the cause of the low oil pressure issue? No idea where the other piece of gasket went....
Gear wear
#232
Haven't fiddled the vvt motor in a long while.
Took the car to autox this weekend and had an absolute blast. I learned I will need a catch can because I was getting some mean clouds of oil during rapid de-accel, even with the 323 gtx valve.
It got worse when I started to hot lap the car at the end, I ran about 4 laps with maybe 1 minute cool down time in between each lap, popped my hood and there was oil everywhere out of the breather filter.
fastest lap was a 1:32, slowest was a 1:50 something. The embarrassing thing is my fastest lap was with leach riding along.
Also picked up a 1995 montego to fix and possible DD, measly sum of $500 and I've made almost all of it back from selling the aftermarket parts off of it
Took the car to autox this weekend and had an absolute blast. I learned I will need a catch can because I was getting some mean clouds of oil during rapid de-accel, even with the 323 gtx valve.
It got worse when I started to hot lap the car at the end, I ran about 4 laps with maybe 1 minute cool down time in between each lap, popped my hood and there was oil everywhere out of the breather filter.
Also picked up a 1995 montego to fix and possible DD, measly sum of $500 and I've made almost all of it back from selling the aftermarket parts off of it
#236
still undecided on what I want to do with the vvt motor, I definitely want it into the purple car, but at what level? Half of me doesn't want to open up the short block, just because of how low mileage it is and how small this turbo is, tops out at around 230 whp, which is a little above what the car is at right now. I plan on doing a BE pump for sure, still undecided on engine managment. Also I have college to think about for the next 2 years, and it's 4 hours away, not a trip I want to do in a turbo autox miata every weekend. And the purple car is starting to become non-daily friendly with 5 points and all, so I figured a cheap miata would be a fun daily. I think Lars daily's an older miata too IIRC
#239
Photos from last month's autox, going back the 28th for the next event. Getting the car aligned this weekend and new rubber, I need to install my catch can and figure out a mounting system, also the car needs to have the downpipe re welded again, seems to be leaking from the flange.
Got this heap running, sounds like the diff has coins rolling around in it, at first I thought it was a loose driveshaft but all the bolts are tight, maybe the diff is starting to go?
Fit 4 tires and 4 wheels in the car, getting new toyo ra1's put on for the fast car
Got this heap running, sounds like the diff has coins rolling around in it, at first I thought it was a loose driveshaft but all the bolts are tight, maybe the diff is starting to go?
Fit 4 tires and 4 wheels in the car, getting new toyo ra1's put on for the fast car
#240
Elite Member
iTrader: (2)
Join Date: Aug 2016
Location: New Fucking Jersey
Posts: 3,890
Total Cats: 143
Have you put new fluid in the diff yet? I hope you don't find surprises in the fluid when you do that... I'd probably start with the fluid to see if that helps anything. Odds are that it's never been changed.