The Definitive "VVT swap into 90-97 chassis" Megathread.
#363
I'm making progress modifying my '94 oil pump to support a crank sensor. I drilled & tapped the cast boss for M6x1. It looks like the oil pump has a little vestigial lip inboard of the sensor mounting point. In the later crank sensor equipped NA's, it looks like this lip became a more pronounced reference point to locate the NA style sensors. Of course, I have a NB style sensor. From what I can tell, the NB pump and sensor configuration allow the sensor to basically pivot freely about the mounting bolt.
I'm going to have to trim that lip off to allow the sensor to seat flush. For those who have dealt with this sensor before, would I be better off giving the sensor enough clearance to pivot freely, or just enough clearance to sit flush but not be able to pivot really at all?
I'm going to have to trim that lip off to allow the sensor to seat flush. For those who have dealt with this sensor before, would I be better off giving the sensor enough clearance to pivot freely, or just enough clearance to sit flush but not be able to pivot really at all?
#364
Former Vendor
Thread Starter
iTrader: (31)
Join Date: Nov 2006
Location: Sunnyvale, CA
Posts: 15,442
Total Cats: 2,104
I would bolt up an OEM damper briefly before cutting anything. You may find that you need to space the sensor out to center it on the trigger wheel, vs. trimming the oil pump.
e: A bit of searching says that's probably wrong. You will need to trim the oil pump to locate the sensor properly. The location of that boss is also different, apparently, so you'll need to compensate for that in your trigger angle setting.
e: A bit of searching says that's probably wrong. You will need to trim the oil pump to locate the sensor properly. The location of that boss is also different, apparently, so you'll need to compensate for that in your trigger angle setting.
#365
I would bolt up an OEM damper briefly before cutting anything. You may find that you need to space the sensor out to center it on the trigger wheel, vs. trimming the oil pump.
e: A bit of searching says that's probably wrong. You will need to trim the oil pump to locate the sensor properly. The location of that boss is also different, apparently, so you'll need to compensate for that in your trigger angle setting.
e: A bit of searching says that's probably wrong. You will need to trim the oil pump to locate the sensor properly. The location of that boss is also different, apparently, so you'll need to compensate for that in your trigger angle setting.
here's the before shot. You can see that the protruding element is radiused.
here's the after shot. I had to file it down to 2mm and stick a 2mm washer behind the sensor.
here you can see where the trigger wheel teeth pass the sensor head. I basically just put the crank sprocket & pulley on the crank without the key so i could spin it against the sensor. That buffed shiny stripe is where the tooth rubbed against the sensor. FYI, the sensor head diameter is just about exactly 16mm if you are trying to center it.
The trigger angle correction sounds intimidating. I guess I'd better start researching that...
#369
Awesome. That's pretty simple. I'll update whether this sensor location requires any correction in TS once I get there.
*UPDATE* I had to advance my timing with trigger wizard 5.5* to get the trigger wheel signal properly sinc'd
*UPDATE* I had to advance my timing with trigger wizard 5.5* to get the trigger wheel signal properly sinc'd
Last edited by wackbards; 05-06-2017 at 02:58 PM. Reason: updated info
#379
91 non return style conversion
Dear Awesome miata gods,
I've read in the 1.8 swap guide from flying miata that if you go standalone you do not need to swap the fuelrails. and thus you have to convert to a non return style fuel system. What will be the best solution since I have the pnp pro for the 90-93 chassis and that the fuel rail is extremely hard to find where I live.
Very Kind regards,
Cedric
I've read in the 1.8 swap guide from flying miata that if you go standalone you do not need to swap the fuelrails. and thus you have to convert to a non return style fuel system. What will be the best solution since I have the pnp pro for the 90-93 chassis and that the fuel rail is extremely hard to find where I live.
Very Kind regards,
Cedric
#380
Your problem is easier to solve than you would think. Just add a fuel pressure regulator inline, with the return pipe connected to the return line and the outlet pipe connected to the returnless fuel rail. That way you're basically putting the fuel return where the original one is instead of next to the fuel tank. That's basically what the returnless system is: It has a constant pressure FPR next to the tank and a short return line.