Billet Water Pump Inlet Adapter - Pre-Order
#85
Former Vendor
Thread Starter
iTrader: (8)
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,185
Total Cats: 57
What would be the interest level of including a lower radiator hose with these? I was tinkering a bit and might have found an off the shelf solution that required minimal trimming to fit.
I'm hoping to get these shipped out on Friday, but can try to source some hoses if those would be valuable to you folks.
Lemme know!
I'm hoping to get these shipped out on Friday, but can try to source some hoses if those would be valuable to you folks.
Lemme know!
#87
What would be the interest level of including a lower radiator hose with these? I was tinkering a bit and might have found an off the shelf solution that required minimal trimming to fit.
I'm hoping to get these shipped out on Friday, but can try to source some hoses if those would be valuable to you folks.
Lemme know!
I'm hoping to get these shipped out on Friday, but can try to source some hoses if those would be valuable to you folks.
Lemme know!
#88
Former Vendor
Thread Starter
iTrader: (8)
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,185
Total Cats: 57
I'll try to confirm fitment on Friday and get some pricing. I can probably fit it in the medium flat rate box with the inlet so no extra there. I'm guessing $20 or so for the hose and a pair of hose clamps.
If anyone has no interest and just wants me to ship there part let me know and I'll try to expedite. I figure if I can help get a complete solution I'll do that, but I also don't want to slow down anyone's progress.
If anyone has no interest and just wants me to ship there part let me know and I'll try to expedite. I figure if I can help get a complete solution I'll do that, but I also don't want to slow down anyone's progress.
#89
I'll try to confirm fitment on Friday and get some pricing. I can probably fit it in the medium flat rate box with the inlet so no extra there. I'm guessing $20 or so for the hose and a pair of hose clamps.
If anyone has no interest and just wants me to ship there part let me know and I'll try to expedite. I figure if I can help get a complete solution I'll do that, but I also don't want to slow down anyone's progress.
If anyone has no interest and just wants me to ship there part let me know and I'll try to expedite. I figure if I can help get a complete solution I'll do that, but I also don't want to slow down anyone's progress.
#95
Former Vendor
Thread Starter
iTrader: (8)
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,185
Total Cats: 57
As soon as I finalize the hose I'll make it public. No sense in not making it public knowledge. For some it makes sense for me to supply it, and for some it doesn't. I'm good either way.
#98
Can you create a version of the EGR blockoff plate out of a thicker material so either a bung can be incorporated or even simply thick enough for a threaded NPT hole so we can source vacuum off the one hole that leads into the intake manifold.
I imagine with a 90° NPT hose barb, one could run a short segment of hose as vacuum reference for your FPR mount solution. Less T's, more compact and out of sight etc.
Last edited by psyber_0ptix; 02-15-2017 at 03:09 PM.
#100
Former Vendor
Thread Starter
iTrader: (8)
Join Date: Mar 2005
Location: Broken Arrow,Ok
Posts: 1,185
Total Cats: 57
The test fit this weekend went well and I think the hose that I had intended on using for my first prototype works just as well for the new ORB version.
My hope was to pick up some locally, but alas they were out of stock.
I've heard from a few of you on interst in having the hose/clamps included. If you can reply here or PM me and let me know if you'd like your parts shipped alone or with the hose that would be helpful. I don't want anyone to have to wait any longer than they need to, but I'm also overboard about testing to make sure things fit and finish is up to my standard.
I should have the hoses on hand later this week. For the initial buyers I can do the hose with two clamps for $16. The Gates PN is 20820 if you'd prefer to source it yourself. We include heavier duty liner worm clamps as well, but I don't have a PN off hand for those.
I'll add a item in our "Extra Items" link on our website shortly for those interested in adding the hose to their order.
Here are a few install pics
My hope was to pick up some locally, but alas they were out of stock.
I've heard from a few of you on interst in having the hose/clamps included. If you can reply here or PM me and let me know if you'd like your parts shipped alone or with the hose that would be helpful. I don't want anyone to have to wait any longer than they need to, but I'm also overboard about testing to make sure things fit and finish is up to my standard.
I should have the hoses on hand later this week. For the initial buyers I can do the hose with two clamps for $16. The Gates PN is 20820 if you'd prefer to source it yourself. We include heavier duty liner worm clamps as well, but I don't have a PN off hand for those.
I'll add a item in our "Extra Items" link on our website shortly for those interested in adding the hose to their order.
Here are a few install pics