Connector Witch Hunt
#361
Since this thread resurfaced I came to think of my four year temporary solution for connecting the Jenvey TPS to my NB unmodified harness.
Do anyone know of a male version of the 3pin TPS connector?
I might have asked this before, but all I remember from my Google-fu last time I checked was that that connector was sensor only.
Do anyone know of a male version of the 3pin TPS connector?
I might have asked this before, but all I remember from my Google-fu last time I checked was that that connector was sensor only.
#362
I just replaced the pigtail for the temperature sensor at the front back of the head (on the reroute block).
Posting because finding this was a bitch and a half.
Link to bmotorsports.com pigtail for 7.99
edit- note, this looks very similar to some other connectors but can be distinguished by the alignment of the slots on the side-
the left one is low,
the right one is high and
the bottom one is in the middle.
Posting because finding this was a bitch and a half.
Link to bmotorsports.com pigtail for 7.99
edit- note, this looks very similar to some other connectors but can be distinguished by the alignment of the slots on the side-
the left one is low,
the right one is high and
the bottom one is in the middle.
Since this thread resurfaced I came to think of my four year temporary solution for connecting the Jenvey TPS to my NB unmodified harness.
Do anyone know of a male version of the 3pin TPS connector?
I might have asked this before, but all I remember from my Google-fu last time I checked was that that connector was sensor only.
Do anyone know of a male version of the 3pin TPS connector?
I might have asked this before, but all I remember from my Google-fu last time I checked was that that connector was sensor only.
The sensible thing is to get a male & female that use the same terminals. This way, you can take your connector off and put another connector on using the same terminals. Then you can use the mate to go to your desired TPS.
Plug (to replace stock NB connector as a drop-in)
CONN-100300
Receptacle (for new throttle). You have this connect to the stock NB harness now that you put CONN-100300 on it. The terminals that come out of the back of the CONN-100320 have wires that run to your new throttle connector.
CONN-100320
#364
I've updated our application list with the NA CLT Connector, Kit, & Pigtail!
In other Miata news, I added some ECU headers and connectors for the NA tonight. I'll be flushing these out and the NB header & connectors in the next few weeks:
https://www.bmotorsports.com/shop/ad...bcat=1&x=0&y=0
#366
SADFab Destructive Testing Engineer
iTrader: (5)
Joined: Apr 2014
Posts: 18,642
Total Cats: 1,866
From: Beaverton, USA
Haven't put them up yet on the Miata list we keep updated but the 4 way coil connectors, 3 way coil connectors, 4 way subharness connectors and 2 way ABS/Knock connectors are on the site and somewhat recently added. Just to cover the below, a connector housing is housing + lock only. Kit is with terminals and seals for you to crimp, pigtails come with 12" / 305mm wire leads and preassembled for those without enough harness length or crimp tools.
4 way subharness plug
Ballenger Motorsports - High Performance Electronics
4 way ignition subharness receptacle
Ballenger Motorsports - High Performance Electronics
2 way abs/knock plug
Ballenger Motorsports - High Performance Electronics
2 way abs/knock receptacle
Ballenger Motorsports - High Performance Electronics
3 & 4 way coil connectors:
Ballenger Motorsports - High Performance Electronics
We had a lot of people asking for these parts, so here they are!
4 way subharness plug
Ballenger Motorsports - High Performance Electronics
4 way ignition subharness receptacle
Ballenger Motorsports - High Performance Electronics
2 way abs/knock plug
Ballenger Motorsports - High Performance Electronics
2 way abs/knock receptacle
Ballenger Motorsports - High Performance Electronics
3 & 4 way coil connectors:
Ballenger Motorsports - High Performance Electronics
We had a lot of people asking for these parts, so here they are!
Mine looks like this.
#368
On a separate note, does anyone have NC ECU Connector info? Detailed images in focus with good lighting of any numbers or markings on them and views of the front would be helpful. Knowing the blade width of the male terminals will help too. Email any info to sales@bmotorsports.com please.
#370
https://www.bmotorsports.com/shop/mazda_miata.php
While I updated the spreadsheet that is kept for this thread, at this point there are errors and missing data in it. I think we've finally come to the point where the list on our page is now more up to date, authoritative, and has more components than the spreadsheet. I still do need to update for better distinction between NA/NB/NC and year ranges but this is one of those side projects where I put in a little time here and there where I am able to.
#374
https://www.bmotorsports.com/shop/pr...oducts_id/1095 (Kit is CONN-75702, Pigtail is CONN-85702). If not, show me what you have, we probably have both sides of it.
https://www.bmotorsports.com/shop/mazda_miata.php