Pcv
#21
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,028
Total Cats: 304
The purpose of the pcv valve is to allow vacuum to be pulled from the crankcase, which is a necessity. However, oil vapor (and depending on how worn your rings are), oil can get into your intake. The purpose of the catch can is to keep oil/ oil vapor out of your intake. The oil won't enter the catch it by itself though, you have to mimick how the pcv system works. This has been done many ways on this site. Easiest way I'd say to do it is use that drawing, but make a baffle on the catch can before the pcv so no oil or vapor can go through the pcv. Then hook pcv to the intake.
Or do like I did and run a slash cut and use the exhaust to pull the vacuum.
Or do like I did and run a slash cut and use the exhaust to pull the vacuum.
#22
The purpose of the pcv valve is to allow vacuum to be pulled from the crankcase, which is a necessity. However, oil vapor (and depending on how worn your rings are), oil can get into your intake. The purpose of the catch can is to keep oil/ oil vapor out of your intake. The oil won't enter the catch it by itself though, you have to mimick how the pcv system works. This has been done many ways on this site. Easiest way I'd say to do it is use that drawing, but make a baffle on the catch can before the pcv so no oil or vapor can go through the pcv. Then hook pcv to the intake.
Or do like I did and run a slash cut and use the exhaust to pull the vacuum.
Or do like I did and run a slash cut and use the exhaust to pull the vacuum.
#23
Junior Member
Thread Starter
Join Date: Jul 2016
Location: pembroke pines, florida
Posts: 128
Total Cats: -59
The purpose of the pcv valve is to allow vacuum to be pulled from the crankcase, which is a necessity. However, oil vapor (and depending on how worn your rings are), oil can get into your intake. The purpose of the catch can is to keep oil/ oil vapor out of your intake. The oil won't enter the catch it by itself though, you have to mimick how the pcv system works. This has been done many ways on this site. Easiest way I'd say to do it is use that drawing, but make a baffle on the catch can before the pcv so no oil or vapor can go through the pcv. Then hook pcv to the intake.
Or do like I did and run a slash cut and use the exhaust to pull the vacuum.
Or do like I did and run a slash cut and use the exhaust to pull the vacuum.
#28
Retired Mech Design Engr
iTrader: (3)
Join Date: Jan 2013
Location: Seneca, SC
Posts: 5,012
Total Cats: 859
For a basic street car, just add a check valve in the hose between PCV valve and intake manifold. Leave exhaust side hose connected from the valve cover, to a location between intake filter and Turbo. If no line on that side, add a little filter.
Add catch cans on track cars or those with worn out engines and massive blow by.
Add catch cans on track cars or those with worn out engines and massive blow by.
Last edited by DNMakinson; 10-31-2016 at 09:24 AM. Reason: Changed "head'" to "valve cover"
#29
SADFab Destructive Testing Engineer
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Like 25% of my build thread is screwed.
Someone should complain and get it fixed.
Just bug he loves dealing with that ****.
#31
Slowest Progress Ever
iTrader: (26)
Join Date: Oct 2007
Location: The coal ridden hills of Pennsylvania
Posts: 6,028
Total Cats: 304
I know it's way late, I apologize. Since 9/5, things just have been "interesting" for me.
Here are 2 photos of my modified valve cover. I welded the PCV shut, the breather I put a vise grip on and wiggled it out, then I drilled and tapped for a (can't remember the NPT thread size) to -12AN adapter. Which I then threaded into the valve cover, and welded it for sealing and strength. The line runs along my downpipe, where I have a slash cut welded into with a check valve.
If you choose to do this, I think it works very well. Suggestions: When you take off the valve cover to drill and tap/ weld, take out the phillips screws on the baffle cover, and cut a piece of scotch brite type material to put in there. Then put the cover back on and the screws back in. My reasoning is, I think this setup actually pulls a lot of vacuum, with could cause a lot of oil to end up in your exhaust due to unrestricted factory valve cover baffling.
Any questions or comments, lay em on me!
Here are 2 photos of my modified valve cover. I welded the PCV shut, the breather I put a vise grip on and wiggled it out, then I drilled and tapped for a (can't remember the NPT thread size) to -12AN adapter. Which I then threaded into the valve cover, and welded it for sealing and strength. The line runs along my downpipe, where I have a slash cut welded into with a check valve.
If you choose to do this, I think it works very well. Suggestions: When you take off the valve cover to drill and tap/ weld, take out the phillips screws on the baffle cover, and cut a piece of scotch brite type material to put in there. Then put the cover back on and the screws back in. My reasoning is, I think this setup actually pulls a lot of vacuum, with could cause a lot of oil to end up in your exhaust due to unrestricted factory valve cover baffling.
Any questions or comments, lay em on me!
#35
SADFab Destructive Testing Engineer
iTrader: (5)
Join Date: Apr 2014
Location: Beaverton, USA
Posts: 18,642
Total Cats: 1,866
Read more. You don't have an understanding of the system.
PCV stands for positive crank case ventilation. You are currently applying no vaccum to the engine, so its just CV (crankcase ventilation)
when in vacuum the intake pulls a vacuum on the valve cover and can suck in oil, so thats why you put a separator there.
PCV stands for positive crank case ventilation. You are currently applying no vaccum to the engine, so its just CV (crankcase ventilation)
when in vacuum the intake pulls a vacuum on the valve cover and can suck in oil, so thats why you put a separator there.