Turbo Smurfette - Build in progress (slow)
#781
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
This is the next fail-aids I need to correct as soon as I can find a reasonable fabricator. May go with Braineacks recommendation and stick the filter out by the fender and just have fabricator build the tight radius piping.
#785
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
The coupler is 2.5" 135° silicone. I cut the silicone down to about an inch just before the radius starts ( just enough to fit over the flange squarely with a clamp) to pull it as close to the turbo as possible. A metal pipe might require some extra length to make room for two clamps and a silicone coupler. BRB I'll grab a picture.
#786
SadFab CEO
iTrader: (3)
Join Date: Sep 2012
Location: your mom's house phoenix, AZ
Posts: 4,560
Total Cats: 1,142
I don't think you'll get a much tighter radius than this.
https://www.summitracing.com/parts/sum-670177/overview/
https://www.summitracing.com/parts/sum-670177/overview/
#790
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
The lamp motors are physically in the way, the actuator arm doesn't interfere at all. I thought about a way to relocate or do something to gain some clearance.
An aluminum pipe will probably gain a bit of space, but not 1". I do worry that because the silicone is creased due to the headlight motor/adjuster that the vacuum will taco it, but maybe I'll just stick a clamp on it to keep the tube from buckling.
I only have mig experience and I don't even have access to much of that stuff since I left academics 2 years ago. Maybe this is where one of those silly intake vband clamps might come in handy if they have flanges in aluminum.
No clue, I'll leave it to the pro's
An aluminum pipe will probably gain a bit of space, but not 1". I do worry that because the silicone is creased due to the headlight motor/adjuster that the vacuum will taco it, but maybe I'll just stick a clamp on it to keep the tube from buckling.
I only have mig experience and I don't even have access to much of that stuff since I left academics 2 years ago. Maybe this is where one of those silly intake vband clamps might come in handy if they have flanges in aluminum.
No clue, I'll leave it to the pro's
#791
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
Maybe @aidandj can cut us a weld stub with the vband mate on a lathe now that he has an EFR sitting in his living room.
#796
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
If i recall, the outlets on some EFR platforms can be cut down for a vband, but nothing about the inlets. Of the 3 EFR625x turbos i've had in my possession, none are inherently vband. ,
#799
Elite Member
iTrader: (37)
Join Date: Apr 2010
Location: Very NorCal
Posts: 10,448
Total Cats: 1,900
Also related: is that a spare compressor cover? Maybe for a 6258?
#800
Elite Member
Thread Starter
iTrader: (4)
Join Date: Mar 2012
Location: Northern VA
Posts: 4,648
Total Cats: 544
If anyone needs to borrow a housing for modification, I have an extra.
A welded elbow directly onto the housing might be the tightest it gets. That 90° might just sneak behind the motor
A welded elbow directly onto the housing might be the tightest it gets. That 90° might just sneak behind the motor