prop valve and trailbraking
#1
prop valve and trailbraking
I've installed a prop valve in my braking system and am having trouble getting my head around what it should feel like during braking.
Long story short, I've installed a bbk in a 2004 msm. The dynalite's have a much smaller piston area (3.00 sq in) than my oem front brakes (2.54sq in) and this has pissed off my abs/ebd. The brakes don't stop well at threshold braking. I've installed a Wilwood prop valve, but have questions about it's adjustment.
This valve apparently cuts the rear brake supply completely until it sees 100# in line pressure, then it is adjustable above that pressure. While I see how this effects threashold braking, what about feathering the brakes/trailbraking? I don't have any real numbers, but I am often on my brakes lightly thru the corner entrance to apex. I'm curious if much braking is done at the racetrack under 100#? and, how putting in a valve that will turn off my rear brakes until I hit 100# would effect my cornering? Can I still use the brakes to help point the car? Or, will it now promote understeer?
Asking this because the car is not licensed for the street. The only test/tune time I have with my local SCCA group is during qualifying... and there's just a lot to think about in addition to how to tune the valve.
Long story short, I've installed a bbk in a 2004 msm. The dynalite's have a much smaller piston area (3.00 sq in) than my oem front brakes (2.54sq in) and this has pissed off my abs/ebd. The brakes don't stop well at threshold braking. I've installed a Wilwood prop valve, but have questions about it's adjustment.
This valve apparently cuts the rear brake supply completely until it sees 100# in line pressure, then it is adjustable above that pressure. While I see how this effects threashold braking, what about feathering the brakes/trailbraking? I don't have any real numbers, but I am often on my brakes lightly thru the corner entrance to apex. I'm curious if much braking is done at the racetrack under 100#? and, how putting in a valve that will turn off my rear brakes until I hit 100# would effect my cornering? Can I still use the brakes to help point the car? Or, will it now promote understeer?
Asking this because the car is not licensed for the street. The only test/tune time I have with my local SCCA group is during qualifying... and there's just a lot to think about in addition to how to tune the valve.
#2
I'm not sure it's wise to run the adjustable prop valve alongside ABS. Could do unpredictable things.
As for trailbraking and rotation, what you are doing is transferring weight forward with the light braking. For the most part, it doesn't really matter which end of the car is making that weight transfer happen (assuming you aren't locking up or anything).
BTW, you can get most of the same effect by just modulating the throttle. 0% throttle is actually a pretty aggressive way to transfer weight forward and it is the drag on the rear contact patches that is doing most of that transfer. I try to keep off the brakes and use throttle modulation instead because the brakes **** away your energy so rapidly. I save the trailbraking for those parts of the track where I need to rotate a LOT and then I'm mindful of the energy loss. In most cases, I've found adjusting the line to be wider so that rotation with throttle alone does the trick increases the minimum corner speed and buys time.
I think I just saw a picture of your car with an oil cooler and intercooler install with the front crash structure substantially altered (looks like you used the oil cooler to tie the car together at the front). Was that your car I'm thinking of? Any more pictures of that? I'm looking for a way to get air around a FAB9 IC to my radiator, but the front crash bar is in the way. /end threadjack.
As for trailbraking and rotation, what you are doing is transferring weight forward with the light braking. For the most part, it doesn't really matter which end of the car is making that weight transfer happen (assuming you aren't locking up or anything).
BTW, you can get most of the same effect by just modulating the throttle. 0% throttle is actually a pretty aggressive way to transfer weight forward and it is the drag on the rear contact patches that is doing most of that transfer. I try to keep off the brakes and use throttle modulation instead because the brakes **** away your energy so rapidly. I save the trailbraking for those parts of the track where I need to rotate a LOT and then I'm mindful of the energy loss. In most cases, I've found adjusting the line to be wider so that rotation with throttle alone does the trick increases the minimum corner speed and buys time.
I think I just saw a picture of your car with an oil cooler and intercooler install with the front crash structure substantially altered (looks like you used the oil cooler to tie the car together at the front). Was that your car I'm thinking of? Any more pictures of that? I'm looking for a way to get air around a FAB9 IC to my radiator, but the front crash bar is in the way. /end threadjack.
#3
I'm not sure it's wise to run the adjustable prop valve alongside ABS. Could do unpredictable things.
As for trailbraking and rotation, what you are doing is transferring weight forward with the light braking. For the most part, it doesn't really matter which end of the car is making that weight transfer happen (assuming you aren't locking up or anything).
BTW, you can get most of the same effect by just modulating the throttle. 0% throttle is actually a pretty aggressive way to transfer weight forward and it is the drag on the rear contact patches that is doing most of that transfer. I try to keep off the brakes and use throttle modulation instead because the brakes **** away your energy so rapidly. I save the trailbraking for those parts of the track where I need to rotate a LOT and then I'm mindful of the energy loss. In most cases, I've found adjusting the line to be wider so that rotation with throttle alone does the trick increases the minimum corner speed and buys time.
I think I just saw a picture of your car with an oil cooler and intercooler install with the front crash structure substantially altered (looks like you used the oil cooler to tie the car together at the front). Was that your car I'm thinking of? Any more pictures of that? I'm looking for a way to get air around a FAB9 IC to my radiator, but the front crash bar is in the way. /end threadjack.
As for trailbraking and rotation, what you are doing is transferring weight forward with the light braking. For the most part, it doesn't really matter which end of the car is making that weight transfer happen (assuming you aren't locking up or anything).
BTW, you can get most of the same effect by just modulating the throttle. 0% throttle is actually a pretty aggressive way to transfer weight forward and it is the drag on the rear contact patches that is doing most of that transfer. I try to keep off the brakes and use throttle modulation instead because the brakes **** away your energy so rapidly. I save the trailbraking for those parts of the track where I need to rotate a LOT and then I'm mindful of the energy loss. In most cases, I've found adjusting the line to be wider so that rotation with throttle alone does the trick increases the minimum corner speed and buys time.
I think I just saw a picture of your car with an oil cooler and intercooler install with the front crash structure substantially altered (looks like you used the oil cooler to tie the car together at the front). Was that your car I'm thinking of? Any more pictures of that? I'm looking for a way to get air around a FAB9 IC to my radiator, but the front crash bar is in the way. /end threadjack.
As far as removing the front structure... I'd beware of removing that flat-boxed in cross tie (in front of radiator opening). After doing that, my hood shakes... somewhat violently when at speed... it rattles side to side near the base of the window. I'm still trying to figure out if it is because of weakened forward structure, or if it's air pressure that is rattling it.
#4
As far as removing the front structure... I'd beware of removing that flat-boxed in cross tie (in front of radiator opening). After doing that, my hood shakes... somewhat violently when at speed... it rattles side to side near the base of the window. I'm still trying to figure out if it is because of weakened forward structure, or if it's air pressure that is rattling it.
Air pressure can definitely make the hood move around though. Just putting NA headlights up and down makes quite a difference.
Thread
Thread Starter
Forum
Replies
Last Post