Trailer flooring
#21
OK I'll bet it was this stuff then:
http://www.rustoleum.com/CBGProduct.asp?pid=14
From what I have read the solvent-based version is much better than the water base version. The above is the solvent (oil base?) version.
http://www.rustoleum.com/CBGProduct.asp?pid=14
From what I have read the solvent-based version is much better than the water base version. The above is the solvent (oil base?) version.
#22
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
I installed a Murphy fold down bed in the front of mine. It stiffened up the front wall, which helped the side to side movement/stress (caused by a sidewall mounted tire rack) and the miata is small enough to merely roll to the rear of the trailer, without unloading it, and still fold out the bed, if you need to sleep at a rest stop, etc.
#23
Elite Member
iTrader: (14)
Join Date: Sep 2009
Location: Birmingham, AL
Posts: 2,101
Total Cats: 180
I have all sorts of **** planned for my gutted 24'. I'm using the linex base dusted with abrasive media and diamondplate in the rear. I also plan on partitioning the hauler in the front for awesome living quarters... including drop down bed/futon, refrigerator, HVAC split system (heat pump), wide screen wall mount, auto-tuning satellite, carpet, maybe even a ****/shower combo.... a rolling bachelor pad
Can't forget about the grill either!
Dark commercial carpet will work best... might not be the softest about will hold up longer.
Can't forget about the grill either!
Dark commercial carpet will work best... might not be the softest about will hold up longer.
Last edited by GeneSplicer; 06-18-2012 at 06:40 PM.
#24
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
Well I decided to go with a two-part solvent based epoxy. After much reading and deliberating I went with Sherwin-Williams Armorseal 1000
ArmorSeal 1000 HS Epoxy - Protective & Marine
It is normally used for concrete floors but many have used it on plywood trailer floors with good success. Enough mix for two gallons costs about $150; it comes in two one gallon containers (epoxy and activator) which are mixed together 1:1. I am laying it down in two coats and applied the first coat tonight (only mixing 1 gallon). The plywood really soaked up the first coat so the second coat will definitely be needed to smooth it out. I am rolling it on. Pics later.
You definitely want to use this stuff in a WELL ventilated area. I had the back ramp and the side door both open, with a light wind blowing through, and the fumes were still quite powerful.
ArmorSeal 1000 HS Epoxy - Protective & Marine
It is normally used for concrete floors but many have used it on plywood trailer floors with good success. Enough mix for two gallons costs about $150; it comes in two one gallon containers (epoxy and activator) which are mixed together 1:1. I am laying it down in two coats and applied the first coat tonight (only mixing 1 gallon). The plywood really soaked up the first coat so the second coat will definitely be needed to smooth it out. I am rolling it on. Pics later.
You definitely want to use this stuff in a WELL ventilated area. I had the back ramp and the side door both open, with a light wind blowing through, and the fumes were still quite powerful.
#27
Elite Member
iTrader: (14)
Join Date: Sep 2009
Location: Birmingham, AL
Posts: 2,101
Total Cats: 180
I called DuPont on their expoy garage kit when at HDracing, they said not to use it as it would crack at the floor seams. Let us know how it goes - still have to do mine, still thinking of linex stuff.
#28
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
Yep SW told me the same thing, but others have had good success with the same stuff in enclosed trailers with plywood floors, reporting that after several years it is still OK.
Thread
Thread Starter
Forum
Replies
Last Post