Post your corner weight scale pics!
#1
Thread Starter
Elite Member
iTrader: (12)
Joined: Jan 2007
Posts: 2,573
Total Cats: 12
From: Hermosa Beach, CA
Post your corner weight scale pics!
Since I just did mine, and no thread seems to document weight, I thought it would be a good idea.
93 1.6l, turbocharger setup, still had ---- in the trunk/passenger footwell. This is without me in it (cross goes to 50.2% with me in it).
93 1.6l, turbocharger setup, still had ---- in the trunk/passenger footwell. This is without me in it (cross goes to 50.2% with me in it).
#4
Wow, big differences(500 lbs) from a full scale NB and a stripped NA. If I can get mine under 2300 with me in it I'll be happy. Mine's a NA with no carpet(roll in bedliner) no gauges(Raceapak) Radio, door speakers, console, stripped wiring harness, custom engine bay harness(tucked) headlight motor delete, anythng unnecessary engine bay delete, no A/C and no PS carbon trunk(you'd be surprised how heave the stock trunk is. 10lb battery, V8R control arms, carbon driveshaft tein mono-flex. Any guess on where I'll be as far as weight? I cant think of anything else that will add/reduce weight. I'm about 165-170
#6
Gutted interior, full doors/power windows, hardtop, half a tank of fuel, OEM jack and small stuff in trunk. Drivers seat/floor area ballasted with ~75kg of lead. Total weight is 1060kg, or ~2340lbs. More weight to come out, both of the car and me
This was after a whole day of taking our time setting ride height, alignment and corner weighing. Couldn't be happier for €150
This was after a whole day of taking our time setting ride height, alignment and corner weighing. Couldn't be happier for €150
#8
Junior Member
Joined: Dec 2010
Posts: 375
Total Cats: 20
From: UK, in Cambridgeshire or wherever work takes me.
F20C car, with no set up work, with 65kg/145lb driver and 3/4 tank of fuel. Fully trimmed interior. Lots of potential for improvement after corner weighting!
Figures in pounds:
Total 2361
LF 567.5 RF 629.5
LR 562 RR 602
Figures in pounds:
Total 2361
LF 567.5 RF 629.5
LR 562 RR 602
#14
1.6L motor/trans. 1993 chassis.
Edit: I guess I should elaborate. This is just about the minimum you can go and still be able to drive it without replacing parts for lighter weight versions. I think I can pull another 15-20 lbs out without trying too hard either.
Gutted, 1.6L drivetrain(motor,trans, diff),
lightweight 13x7" wheels,
front and rear bumper covers only.
headlight covers,but no lights or rear finish pane.
Partially gutted rear decklid(need another set of hood pins to remove the heavy hinges)
Hood latch assembly removed, stock hood otherwise.
rewired for MS1 and stock 1.6L alternator, lawn and garden battery($20) in stock location.
No windshield or frame.
Kirkey seat on stock NB slider. (no pass. seat.)
Partially gutted pass. door. Drives door still retains it's door bar and upper inner sill bar(heavy).
Note: No bar/cage (Yet)
Edit: I guess I should elaborate. This is just about the minimum you can go and still be able to drive it without replacing parts for lighter weight versions. I think I can pull another 15-20 lbs out without trying too hard either.
Gutted, 1.6L drivetrain(motor,trans, diff),
lightweight 13x7" wheels,
front and rear bumper covers only.
headlight covers,but no lights or rear finish pane.
Partially gutted rear decklid(need another set of hood pins to remove the heavy hinges)
Hood latch assembly removed, stock hood otherwise.
rewired for MS1 and stock 1.6L alternator, lawn and garden battery($20) in stock location.
No windshield or frame.
Kirkey seat on stock NB slider. (no pass. seat.)
Partially gutted pass. door. Drives door still retains it's door bar and upper inner sill bar(heavy).
Note: No bar/cage (Yet)
Last edited by tpwalsh; 02-17-2013 at 11:58 AM.
#17
1.6L motor/trans. 1993 chassis.
Edit: I guess I should elaborate. This is just about the minimum you can go and still be able to drive it without replacing parts for lighter weight versions. I think I can pull another 15-20 lbs out without trying too hard either.
Gutted, 1.6L drivetrain(motor,trans, diff),
lightweight 13x7" wheels,
front and rear bumper covers only.
headlight covers,but no lights or rear finish pane.
Partially gutted rear decklid(need another set of hood pins to remove the heavy hinges)
Hood latch assembly removed, stock hood otherwise.
rewired for MS1 and stock 1.6L alternator, lawn and garden battery($20) in stock location.
No windshield or frame.
Kirkey seat on stock NB slider. (no pass. seat.)
Partially gutted pass. door. Drives door still retains it's door bar and upper inner sill bar(heavy).
Note: No bar/cage (Yet)
Edit: I guess I should elaborate. This is just about the minimum you can go and still be able to drive it without replacing parts for lighter weight versions. I think I can pull another 15-20 lbs out without trying too hard either.
Gutted, 1.6L drivetrain(motor,trans, diff),
lightweight 13x7" wheels,
front and rear bumper covers only.
headlight covers,but no lights or rear finish pane.
Partially gutted rear decklid(need another set of hood pins to remove the heavy hinges)
Hood latch assembly removed, stock hood otherwise.
rewired for MS1 and stock 1.6L alternator, lawn and garden battery($20) in stock location.
No windshield or frame.
Kirkey seat on stock NB slider. (no pass. seat.)
Partially gutted pass. door. Drives door still retains it's door bar and upper inner sill bar(heavy).
Note: No bar/cage (Yet)
I don't corner weight, but I do have the over all weight of me car.
Full interior w/ aluminum racing driver seat, passenger seat stock, full MiataCage and a half tank--2020 lbs