Lets Discuss Steering: Wheels, Hubs, Quick release, ect... Also a race wheel DIY.
#61
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
+1 on splined hub hate. Non indexing, sticky, wobbly **** design. I don't care if they are made from unicorn tears to milspec tolerances, it's a **** design.
Most our cars use between a 20-30mm spacer. Ebay. Momo 5702 steel or Daikei cast adapter, depending on usage.
Momo 78's almost exclusively, usually 350mm.
We started using NRG QR hubs years ago after I paid retail for a Works Bell QR hub and was amazed at how well it worked. Equally amazed at how they could charge $380 for them. Every car on our team runs the same QR hub. This allows quick interchange between cars. This became quite useful when we often ran multiple cars in endurance races with drivers doing stint 1 in car A then stint 2 in car B. Pile of spare steering wheels on pit wall all wired with the same PTT button.
Conservatively, I'd estimate our team has something like 10,000hrs on these including 7x Thunderhill 25 hrs and maybe 50x WERC 3hrs an not a single hiccup. One of my oldest ones, got a little dirty and felt slow to "snap" in. Cleaned it with some IPA (not beer), added some tri flow and it's been fine for years since.
Honestly, it stings a bit to be a customer of NRG buying what is blatant copy of the Works Bell but it is 1/3rd the price and works. My answer (rationalization) is that Works Bell should offer a Chinese or even Taiwanese version for say $199 to get some of their market share back. I know what it costs to make something like this. Using ABEC 5 bearings and 7075 T-6 I could make these and sell for $159 at a profit. So no good reason for WB to charge what they do other than typical Japanese home market stubbornness.
/rant
![](http://949racing.com/supermiata/Steering_Wheel_2.jpg?)
![](http://949racing.com/supermiata/Steering_Wheel_1.jpg?)
Lawyer button reside in that hole. Gosh, ours must have fallen out!
Most our cars use between a 20-30mm spacer. Ebay. Momo 5702 steel or Daikei cast adapter, depending on usage.
Momo 78's almost exclusively, usually 350mm.
We started using NRG QR hubs years ago after I paid retail for a Works Bell QR hub and was amazed at how well it worked. Equally amazed at how they could charge $380 for them. Every car on our team runs the same QR hub. This allows quick interchange between cars. This became quite useful when we often ran multiple cars in endurance races with drivers doing stint 1 in car A then stint 2 in car B. Pile of spare steering wheels on pit wall all wired with the same PTT button.
Conservatively, I'd estimate our team has something like 10,000hrs on these including 7x Thunderhill 25 hrs and maybe 50x WERC 3hrs an not a single hiccup. One of my oldest ones, got a little dirty and felt slow to "snap" in. Cleaned it with some IPA (not beer), added some tri flow and it's been fine for years since.
Honestly, it stings a bit to be a customer of NRG buying what is blatant copy of the Works Bell but it is 1/3rd the price and works. My answer (rationalization) is that Works Bell should offer a Chinese or even Taiwanese version for say $199 to get some of their market share back. I know what it costs to make something like this. Using ABEC 5 bearings and 7075 T-6 I could make these and sell for $159 at a profit. So no good reason for WB to charge what they do other than typical Japanese home market stubbornness.
/rant
![](http://949racing.com/supermiata/Steering_Wheel_2.jpg?)
![](http://949racing.com/supermiata/Steering_Wheel_1.jpg?)
Lawyer button reside in that hole. Gosh, ours must have fallen out!
![](http://949racing.com/supermiata/Lawyer_Button.jpg?)
__________________
Last edited by emilio700; 03-11-2015 at 01:59 PM.
#62
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
![](http://begoodphotography.smugmug.com/Photos-By-Request/OG-racin/i-Bv3TMqg/0/M/IMG_0331-M.jpg)
Emilio,
I would strongly suggest a sparco/momo adapter hub, they are a collapsible design. as the works bell is not. I think they cost about the same. I personally did have a works bell hub adapter fail on me. the casting cracked right in half. that was on a ls1 miata with no power steering (very hard to turn the wheel)
__________________
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
OG Racing
Your Source For Motorsports Safety Equipment
WWW.OGRACING.COM
800.934.9112
703.430.3303
info@ogracing.com
#63
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Emilio,
I would strongly suggest a sparco/momo adapter hub, they are a collapsible design. as the works bell is not. I think they cost about the same. I personally did have a works bell hub adapter fail on me. the casting cracked right in half. that was on a ls1 miata with no power steering (very hard to turn the wheel)
I would strongly suggest a sparco/momo adapter hub, they are a collapsible design. as the works bell is not. I think they cost about the same. I personally did have a works bell hub adapter fail on me. the casting cracked right in half. that was on a ls1 miata with no power steering (very hard to turn the wheel)
__________________
#65
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
yes I made mine work. until I pulled my airbag sensors out and at some point disconnected the horn wiring since the two are combined. I still havent found where I created the break in the horn wiring. You connect both horn button wires to the two contacts on the QR, you connect 1 QR wire to the horn wire from the clock spring, and then you ground the other one. I just ground it to the hub adapter which normally will make an electrical connection to ground through the steering column.
#71
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Found another option that seems to be a bit better: GuardianDesigns custom steering wheels and more... - MX-5 Miata Forum
Thread
Thread Starter
Forum
Replies
Last Post