I want to pound my Miata in the ass - Hardcore
#21
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
For the Cobra, do you know offhand what the spline count is on the end of the halfshaft that mates with the inboard CV? Not the spline that goes into the diff, the one that goes into the inside component of the CV a.k.a the tripod. It is not something you can check unless the boot is off of the CV.
#22
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I think it may be that the Explorer housing is significantly taller than the t-bird housing. For one thing there is a decent gap between the ring gear and the top-inside surface of the housing. For another, there are a lot of cooling fins and protrusions on the top of the housing. So the distance from the center of the axle to the top of the housing could be significantly taller on the Explorer housing.
T-Bird diff housing (In a FFR Cobra frame)
![](http://parts.factoryfive.com/newcatalog/chassis/pictures/irs.jpg)
Steins t-bird housing (can't see top but notice no fins)
![](http://i51.photobucket.com/albums/f357/68017/HPIM0847.jpg)
T-Bird diff housing (In a FFR Cobra frame)
![](http://parts.factoryfive.com/newcatalog/chassis/pictures/irs.jpg)
Steins t-bird housing (can't see top but notice no fins)
![](http://i51.photobucket.com/albums/f357/68017/HPIM0847.jpg)
#23
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Thanks Stein, no worries. The two finger measurement is all I need to know, and somehow that method of measurement fits the theme of this thread.
I talked with the Driveshaft Shop this morning and they are looking into a driveshaft option based on the measurements I provided. I'll let you guys know what I find out.
I talked with the Driveshaft Shop this morning and they are looking into a driveshaft option based on the measurements I provided. I'll let you guys know what I find out.
#26
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
More information on Driveshaft Shop halfshaft options here. Linking instead of repeating. Bandit you probably saw this already.
http://forum.miata.net/vb/showthread...=366129&page=3
http://forum.miata.net/vb/showthread...=366129&page=3
#27
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Update: Currently modifying a subframe I am going to swap in. I am cutting the excess fins off of the Explorer housing and using a template I made of the floor/gas-tank to check for clearance. It looks like I will be able to raise the diff about 2.5"-3" above where it was before which should give me the halfshaft angle reduction that I need.
Hell if I get this done quickly enough I will be able to track test it next weekend.
Hell if I get this done quickly enough I will be able to track test it next weekend.
#28
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Updates
Fins removed from top of differential
![](https://lh6.ggpht.com/_jh2HiMm4nKQ/THAjzq5jw7I/AAAAAAAACng/3q5KAnYQHOE/s640/P8210143.JPG)
Modified subframe
![](https://lh6.ggpht.com/_jh2HiMm4nKQ/THAj4i-rKlI/AAAAAAAACnk/3-XkX1J-nHg/s640/P8210144.JPG)
![](https://lh4.ggpht.com/_jh2HiMm4nKQ/THAj-bqO6QI/AAAAAAAACno/XPo0C6VAwho/s640/P8210145.JPG)
Welds are not pretty but they are very beefy. Note the reinforcement plates. Also note the front diff mount, and the through hole mounts added for the diff.
New mounting location is about 2" higher in the car so it should take care of the problem. All I have to do is wait for the paint to dry, remove the old subframe, swap over the control arms, install this subframe, install the diff, and reinstall the rebuilt halfshafts.
Fins removed from top of differential
Modified subframe
Welds are not pretty but they are very beefy. Note the reinforcement plates. Also note the front diff mount, and the through hole mounts added for the diff.
New mounting location is about 2" higher in the car so it should take care of the problem. All I have to do is wait for the paint to dry, remove the old subframe, swap over the control arms, install this subframe, install the diff, and reinstall the rebuilt halfshafts.
#30
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
All that in 100 degree temps...what a bad ***. That's what I call motivation. I, on the other hand, spent the day installing part of a drip irrigation system at the house. I sure would like at least a little rain sometime before the year is up. I am finally picking up the Miata tomorrow so some work may actually progress on it for a change.
#31
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
My excursions outside today were as brief as possible. It is freaking hot people. August in South Texas FTL. 100F+ temps with 107F+ heat factor. Hell it is well after 10 pm here now and the heat index is 97F. The only nice thing about it, and I do mean ONLY, is that black spray paint sitting in the hot sun dries very, very quickly. It is like I baked it on.
If I were installing drip irrigation today I would have had it irrigating me during the installation process.
Just got back in from dropping the subframe. Though I expected it would not be too bad, it was even easier than I thought. Going from sitting inside getting motivated to do it, to the subframe out of the car and sitting behind it in the driveway, took less than 30 minutes, single-handed. Pneumatic tools FTW.
Tomorrow I use rlogan's pressure washer to remove exploded cv grease and 16 years of road grime from the old subframe. Then the suspension gets swapped over to the new subframe. Then it all goes in the car.
If I were installing drip irrigation today I would have had it irrigating me during the installation process.
Just got back in from dropping the subframe. Though I expected it would not be too bad, it was even easier than I thought. Going from sitting inside getting motivated to do it, to the subframe out of the car and sitting behind it in the driveway, took less than 30 minutes, single-handed. Pneumatic tools FTW.
Tomorrow I use rlogan's pressure washer to remove exploded cv grease and 16 years of road grime from the old subframe. Then the suspension gets swapped over to the new subframe. Then it all goes in the car.
Last edited by ZX-Tex; 08-22-2010 at 03:00 PM.
#32
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
It's in. No *** pounding required though the clearance between the top of the diff and the gas tank is close. I added a heavy foam spacer in between the two just to be safe. It could not be any higher in the car than where I have it now without removing the gas tank. The pinion angle also looks pretty good as well.
![](https://lh5.ggpht.com/_jh2HiMm4nKQ/THFJRhcxcoI/AAAAAAAACoA/DsIUiCLJGY0/s912/P8220154.JPG)
#33
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
UPDATE:
The suspension and halfshafts are back in the car and everything is looking good. The halfshaft angle is much, much better. At full suspension travel they are actually sloping downward towards the outboard end; at the midpoint of the suspension travel they should be very close to level.
I think I have this one solved though I will know for sure when I get it to the track. Hell if I ever do another rear differential conversion I'll just modify the stock subframe and save money on the conversion kit. This one was not too bad, but with a Thunderbird style housing it would be even easier. It makes me want to drop an 8.8 Ford truetrac into the turbo car as a preemptive measure
The suspension and halfshafts are back in the car and everything is looking good. The halfshaft angle is much, much better. At full suspension travel they are actually sloping downward towards the outboard end; at the midpoint of the suspension travel they should be very close to level.
I think I have this one solved though I will know for sure when I get it to the track. Hell if I ever do another rear differential conversion I'll just modify the stock subframe and save money on the conversion kit. This one was not too bad, but with a Thunderbird style housing it would be even easier. It makes me want to drop an 8.8 Ford truetrac into the turbo car as a preemptive measure
![](https://www.miataturbo.net/images/smilies/smile.gif)
#36
Elite Member
Thread Starter
iTrader: (15)
Join Date: Dec 2007
Location: San Antonio, Texas
Posts: 4,847
Total Cats: 27
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
![](https://www.miataturbo.net/images/smilies/smile.gif)
Thread
Thread Starter
Forum
Replies
Last Post
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM