Hustler's new engine: help him pick parts, ya'll ( a thread for power tops)
#191
Tour de Franzia
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Eventually I'll have a 10.5:1 engine, bowl work, fancy cams, BE oil pump, SM damper, Skunk t-body, maybe 180whp by then. For now, just 120whp or so on a 9.5:1 bottom end, we'll see if I can't keep up with the FI guys.
#196
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Just for some comparison, in what Husler is trying to accomplish with his next motor.
here is my last dyno run trying to get the VVT sorted.
it is a '94 block decked .020", ACL bearings, ST 11:1 84mm pistons, stock crank & rods, 2001 VVT head with diy port clean up, stock cams, square top IM, RB header, cat delete, SM exaust. Toyota COP, home brew CAI, DIYAutotune VVTuner & DIYPnP ecu.
I have just installed a Skunk2 TB and rewired the TPS (because the TPS adaptor from Skunk will not work and I had to use a '99 TPS sensor) (too bad I sent Hustler my 01 TPS connector!)
here is my last dyno run trying to get the VVT sorted.
it is a '94 block decked .020", ACL bearings, ST 11:1 84mm pistons, stock crank & rods, 2001 VVT head with diy port clean up, stock cams, square top IM, RB header, cat delete, SM exaust. Toyota COP, home brew CAI, DIYAutotune VVTuner & DIYPnP ecu.
I have just installed a Skunk2 TB and rewired the TPS (because the TPS adaptor from Skunk will not work and I had to use a '99 TPS sensor) (too bad I sent Hustler my 01 TPS connector!)
#200
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Just for some comparison, in what Husler is trying to accomplish with his next motor.
here is my last dyno run trying to get the VVT sorted.
it is a '94 block decked .020", ACL bearings, ST 11:1 84mm pistons, stock crank & rods, 2001 VVT head with diy port clean up, stock cams, square top IM, RB header, cat delete, SM exaust. Toyota COP, home brew CAI, DIYAutotune VVTuner & DIYPnP ecu.
I have just installed a Skunk2 TB and rewired the TPS (because the TPS adaptor from Skunk will not work and I had to use a '99 TPS sensor) (too bad I sent Hustler my 01 TPS connector!)
here is my last dyno run trying to get the VVT sorted.
it is a '94 block decked .020", ACL bearings, ST 11:1 84mm pistons, stock crank & rods, 2001 VVT head with diy port clean up, stock cams, square top IM, RB header, cat delete, SM exaust. Toyota COP, home brew CAI, DIYAutotune VVTuner & DIYPnP ecu.
I have just installed a Skunk2 TB and rewired the TPS (because the TPS adaptor from Skunk will not work and I had to use a '99 TPS sensor) (too bad I sent Hustler my 01 TPS connector!)
__________________