When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
Purchased this and installed last night. I have not tested it on the track yet, but the Denso part does fit. The sock part does seem to have more "structure" inside so that it can't be squeezed flat like the previous sock that came with my DW200 pump. It feels similar to the OEM sock that was on the car. That extra structure could make the difference, or maybe it's the sock material is better at trapping the fuel. If this doesn't work i guess I'm looking at a surge tank or one of the Holley HydraMats.
I was also having some long left-hand turn fuel starvation issues. 99 with LS1 swap. Baffle is fine, fuel tank is clean. The sock I removed was in fine condition by the looks of it. The tank was half full when I was having this problem.
Holley hydramat is not cheap but works amazingly well. I'm a believer. I had to find a solution on the exocet because of the shitty fuel tank angle required and since installing it I have had zero issues on a turbo car. The larger magnet mount kit they offer works perfectly in the miata fuel tank.
Holley hydramat is not cheap but works amazingly well. I'm a believer. I had to find a solution on the exocet because of the shitty fuel tank angle required and since installing it I have had zero issues on a turbo car. The larger magnet mount kit they offer works perfectly in the miata fuel tank.
Curious which Hydramat you used as I'd think the tank baffle might get in the way. I'm assuming you used some sort of adapter kit to transition from the pump inlet (not sure what size that is) via some fuel-compatible hose to the AN fitting on the hydramat using a hose barb connection. Their site sells some fittings and such and hose, but it's the connection to the pump inlet I'm not sure about.
I'm using a Walbro 190LPH-HP with a Radium adapter on the pump and the 15" x 8" hydramat cross in a 99 miata fuel tank. I had fuel starvation issues at anything under 1/4 tank even in a straight line because of the exocet tank mounting angle. But after switching to the setup below I can go down to almost nothing in the tank.
It looks like Radium changed the adapter, pretty sure mine was a barb and not an AN fitting. You could convert the hydramat NPT to a barb and the Radium fitting to a barb and just run their submersible hose or go AN fittings on both. My concern with an AN line would be that it might not be flexible enough. It is a tight space and ideally you would use the Radium PTFE flexible hose (link above) with barbs. The hose does need to be a little long as you need space to be able to mount the hydramat and get it aligned while having the pump assembly tilted to the side.
The cross lets you get some side coverage for slosh and nestles down into the factory pickup spot beside the baffle perfectly. I oriented it so the short ends point outwards and the long ends run front to rear. I put the long rear part under the rear baffle and it fits perfectly. The bigger magnet mounts that holley sells are strong as hell and it won't move at all.
I changed to the factory sock last nigh. Just comparing the size and angle of the Denso sock to the aftermarket one it looks like the Denso sock is bigger and will reach deeper in the tank.
That brown one is the aftermarket sock? It's the completely wrong shape, which would make a big difference in what tank level it began to starve at... The Denso one (assuming that's the clean white new one) is similar shape/size as factory.
Agreed. Did the same back in September, the Denso sock also seems to have more internal structure or volume, so I hope it works out. Haven't been on track to test it yet.
I experienced fuel starvation with my 90 SM at Sebring turn 1 this past november. Once it dropped below 1/8th tank, it would cut off mid corner and wouldn't kick back on until almost turn 3.... lol
I won't be starting a race with less than 1/2 tank again.....
I have run the car down to fumes during a 90 min enduro at Daytona in May of last year, so I was sorta surprised when this happened during my Sebring race
As Ryan pointed out, the brown sock will not work. Despite it's simple appearance, the OEM tank, sock, pickup and baffles work extremely well. Easily feeding an engine at sustained 1.5g down to about 1 gallon. If you have a problem with fuel starvation with anything more than 2 gallons in the tank, you have a pinhole in the sock. This is not conjecture, guess or something we read on the interweb. You may not even be able to find the pinhole, but trust us, it's there.
You may also notice, upon dismantling an OEM pump/sock where there are slight wear marks in the baffle plate inside the tank. That is where the sock rests. That location is Critical to proper scavenging. Change the pump or sock so the sock isn't resting in that part of the baffle and the carefully engineered scavenging system will not work. Walbro and Deatchworks install kits put the replacement socks in the right spot. But also look at your fuel pump install. If the assembly is significantly shorter or longer than OEM, the sock will either be crimped or not touching the baffle in the right spot.
Using E85 will cause the socks to wear. A car run on gas might have it sock last forever if not disturbed. That same car switched to E85 late in life will usually kill the sock in a year or so. We usually switch both fuel filter and sock after the first track weekend on any new builds after switching to E85.
On E85, the sock becomes a wear item and should be swapped at least every two years. Ditto fuel filters.