90 Miata w/Greddy Kit I just Picked Up - Some Opinions Please
#21
Somebody smarter than me should also post the limits of the MSD box... how much it will pull based on what parameters just for info.
Edit... never mind, I found it:
The MSD unit retards the timing 3° per pound of boost pressure with no more that 6° of retard being allowed. When no boost pressure is present, the ignition runs at the factory timing. These settings are fixed and cannot be adjusted. With that said, you can still run your Miata advanced to 14° of timing and when it boost it will retard back to a safe 8°. If knock is still present then set your back back a little. It's a little basic but it gets the job done.
Edit... never mind, I found it:
The MSD unit retards the timing 3° per pound of boost pressure with no more that 6° of retard being allowed. When no boost pressure is present, the ignition runs at the factory timing. These settings are fixed and cannot be adjusted. With that said, you can still run your Miata advanced to 14° of timing and when it boost it will retard back to a safe 8°. If knock is still present then set your back back a little. It's a little basic but it gets the job done.
#22
The MSD unit retards the timing 3° per pound of boost pressure with no more that 6° of retard being allowed. When no boost pressure is present, the ignition runs at the factory timing. These settings are fixed and cannot be adjusted. With that said, you can still run your Miata advanced to 14° of timing and when it boost it will retard back to a safe 8°. If knock is still present then set your back back a little. It's a little basic but it gets the job done.
#23
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,729
Total Cats: 4,126
No it doesn't start pulling untill 4psi. The Bipes ACU was originally a mod for this unit to allow for more timing and adjustabitily controls. He ended up just making a unit to replace it all together.
#26
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Sounds like you're really on top of it. Once you get your i/c piping improved, you'll flow so muh better than you will make the same amount of power at less boost.
If you have the blue injectors, I would adjust the boost controller to 5 or 6 psi until you get to the dyno. The walbro 255 doesn't flow well at higher pressures, even if it is the designated hp model. It might still be borderline at 8 psi with the tan colored 1.8 injectors and the 255. I can't get 8 psi out of my stock 1.6 injectors and my fuel pump flows at high pressures much better than yours. You may also want to open up the vortec fpr and measure the disk size, which will let you know what your rise is. Or get a fuel pressure gauge on there to see what that 255 does to your idle pressure.
I'm also running the msd sebring unit. It's fine, and you could always add an rpm trigger to it for almost no cost (I haven't). The bipes is better because it's adjustable and dynamic, but if you're going to replace it, I'd go ahead step up to a more capable piggyback such as emanage, which will allow you to run bigger injectors and really dial in your fueling and timing.
What's funny is my car looks ok in person and like hot *** in photos. Weird eh?
If you have the blue injectors, I would adjust the boost controller to 5 or 6 psi until you get to the dyno. The walbro 255 doesn't flow well at higher pressures, even if it is the designated hp model. It might still be borderline at 8 psi with the tan colored 1.8 injectors and the 255. I can't get 8 psi out of my stock 1.6 injectors and my fuel pump flows at high pressures much better than yours. You may also want to open up the vortec fpr and measure the disk size, which will let you know what your rise is. Or get a fuel pressure gauge on there to see what that 255 does to your idle pressure.
I'm also running the msd sebring unit. It's fine, and you could always add an rpm trigger to it for almost no cost (I haven't). The bipes is better because it's adjustable and dynamic, but if you're going to replace it, I'd go ahead step up to a more capable piggyback such as emanage, which will allow you to run bigger injectors and really dial in your fueling and timing.
What's funny is my car looks ok in person and like hot *** in photos. Weird eh?
Wow guys, thanks for all the thoughts and advice.
I'll check on the injectors when I get back in town. I'll also inquire with the pre-previous owner who actually did all the mods about the vortech.
The MSD is hiding down by the passenger side shock tower. Fits there rather nicely actually, although it doesn't seem to actually be fastened to anything...yet.
As for the IC plumbing, I'm not happy with it at all. I made it a little better than it was when I picked it up, but I've actually already downloaded a bunch of pics from this forum even before the suggestion.
Thanks again for the advice. A little confused though, samnavy says the car should be fine at 8, and even 10psi (assuming everything is functioning correctly) and ben is advising a bit more caution. Are you assuming somethings been missed in the buildup of this car ben, or are you just advising that I should do an in-depth dive into where the car actually is before being comfortable with it?
I like to do things correctly, so I tend to err on the side of caution myself.
Will post more pics when I get back in town as well. The car photographs well. It's a bit rougher in person.
I'll check on the injectors when I get back in town. I'll also inquire with the pre-previous owner who actually did all the mods about the vortech.
The MSD is hiding down by the passenger side shock tower. Fits there rather nicely actually, although it doesn't seem to actually be fastened to anything...yet.
As for the IC plumbing, I'm not happy with it at all. I made it a little better than it was when I picked it up, but I've actually already downloaded a bunch of pics from this forum even before the suggestion.
Thanks again for the advice. A little confused though, samnavy says the car should be fine at 8, and even 10psi (assuming everything is functioning correctly) and ben is advising a bit more caution. Are you assuming somethings been missed in the buildup of this car ben, or are you just advising that I should do an in-depth dive into where the car actually is before being comfortable with it?
I like to do things correctly, so I tend to err on the side of caution myself.
Will post more pics when I get back in town as well. The car photographs well. It's a bit rougher in person.
#28
Junior Member
Thread Starter
Join Date: Oct 2006
Location: Detroit Area, MI
Posts: 226
Total Cats: 0
Thanks Ben. Same as this car, much nicer in pics
Talked to the previous owner. It's got the stock injectors, but he wasn't sure about the disc size in the vortec.
So, from what you guys are saying, I should definitely bring it back down to 6psi right?
So, what do I need to upgrade to run 8psi, or even 10?
Looked at the crank pulley, seems good. Apparently, the pre-previous owner pulled the pulley off when he did the greddy kit. It was fine, and then he reinstalled with a new key and loctite.
Man, can't wait to get home and actually drive this car again...haven't driven it since the test drive.
Talked to the previous owner. It's got the stock injectors, but he wasn't sure about the disc size in the vortec.
So, from what you guys are saying, I should definitely bring it back down to 6psi right?
So, what do I need to upgrade to run 8psi, or even 10?
Looked at the crank pulley, seems good. Apparently, the pre-previous owner pulled the pulley off when he did the greddy kit. It was fine, and then he reinstalled with a new key and loctite.
Man, can't wait to get home and actually drive this car again...haven't driven it since the test drive.
#32
Agreed, the brace will stiffen up the front end to the point that you'll push like a big dog. On the street it'll feel a little tighter and you'll think you've got more control... but it'll actually lower the handling limits.
I have yet to see a skidpad comparison of with or without a brace, but it was worth a full second to me on a 50sec autocross course.
I have yet to see a skidpad comparison of with or without a brace, but it was worth a full second to me on a 50sec autocross course.
#34
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,729
Total Cats: 4,126
If you have the original disc in the vortech you are trying to push 140psi of fuel into the rail. ([12 x 8] + 48). Something the pump cannot do.
Depending on the the pump, your maxing out at 120psi (Hp) or 80psi (Standard).
At 80psi those injectors are good for about 155BHP or 130rwhp (4-5psi).
At 120psi those injectors are good for about 190BHP or 160rwhp (5-6psi).
A 8psi GReddied miata should be putting down around 180rwhp. Chances are you are running lean past 5.5k. Not to mention adding a lot of fuel pressure in the rail. Most suggest no more than 100psi.
That being said, 240cc injectors (1.8L) are good for around 210BHP or 175rwhp with 110psi in the rail. You can acheive 110psi with the vortech with 8psi of boost by use of a 8:1 ratio disc. ([8 x 8] + 48). Closer in lines to where you power levels should be.
The best way to figure out what's going on is a trip to the dyno with a wideband hooked up. Or running one yourself (worth the $200 in gold).
At least throwing a fuel pressure guage on there and reading the levels in boost gives you a better understanding of how much fuel you are providing and limited to.
Listen for ping in boost too...that's the engine killer.
#35
Water methanol injection and some1.8 injectors will put you at 10+ psi easily, you could even relax the settings on the msd as well and run more timing there to make some real power. with WI 200 whp is possible on th e1.6's it helps effeciency that much get in on the group buy or do some reseaerch and find a product you like. the simple ones are quite effective though. nice car man.
#37
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
The msd sebring timing controller is not adjustable in anyway. Possibly you could restrict the signal tube to delay pulling timing, but there is no adjustment possible. That's why the bipes is superior.
Water methanol injection and some1.8 injectors will put you at 10+ psi easily, you could even relax the settings on the msd as well and run more timing there to make some real power. with WI 200 whp is possible on th e1.6's it helps effeciency that much get in on the group buy or do some reseaerch and find a product you like. the simple ones are quite effective though. nice car man.