MS3PnP and MTX-L ... not talking
#1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Hi guys
I have had my 96 running on the MS3pnp for a few weeks and just got around to installing the inter cooler and MTX-L wide band. I had the yellow signal wire on the MTX-L wired to the stock signal wire by the cas/coils but TS was showing 10.2 AFR.
I unpluged that signal wire and checked it with a meter and it was showing around 2.4 V..
I have the wide band cal. set to the custom in TS with 0 v to 7.35 and 5.0v to 22.4
It seems like the MS just does not see the wideband output.
I ran a wire right to the MS and tapped into the 3C wire and still the MS acts like no signal.
Gauge on the MTX-L it working and moving (14.x to 16.x up and down with idle and throttle) .
Car starts and idles fine ( a little high on the idea but have yet to tune that)...
This is not the first miata I have set up a MS and wideband on but first for having something like this happen.
Anyone seen something like this or have an idea what to check next?
Thanks
Matt
I have had my 96 running on the MS3pnp for a few weeks and just got around to installing the inter cooler and MTX-L wide band. I had the yellow signal wire on the MTX-L wired to the stock signal wire by the cas/coils but TS was showing 10.2 AFR.
I unpluged that signal wire and checked it with a meter and it was showing around 2.4 V..
I have the wide band cal. set to the custom in TS with 0 v to 7.35 and 5.0v to 22.4
It seems like the MS just does not see the wideband output.
I ran a wire right to the MS and tapped into the 3C wire and still the MS acts like no signal.
Gauge on the MTX-L it working and moving (14.x to 16.x up and down with idle and throttle) .
Car starts and idles fine ( a little high on the idea but have yet to tune that)...
This is not the first miata I have set up a MS and wideband on but first for having something like this happen.
Anyone seen something like this or have an idea what to check next?
Thanks
Matt
![](https://forum.miata.net/vb/miata_images/statusicon/user_offline.gif)
![](https://forum.miata.net/vb/miata_images/buttons/quote.gif)
#2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Do you have the MTXL serial programming connector attached by any chance? (ie: plugged into the gauge, not necessarily plugged into a computer)
The MTXL does a stupid thing where it wont send out a signal if the program plug thing is attached at all. (well, not via the 2.5mm jack output anyway, unsure on the bare wire voltage method since my old ECU didnt use it)
The MTXL does a stupid thing where it wont send out a signal if the program plug thing is attached at all. (well, not via the 2.5mm jack output anyway, unsure on the bare wire voltage method since my old ECU didnt use it)
#6
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Ok moved the signal wire to the rear O2 sensor and changed the J5 to rear but still the same.
After that I made a new project in TS and reloaded it with the base tune. Then installed the wideband and setting in TS but still the same.. the AFR just bounces a little just like it has no calibration ( just like the tps will until you calibrate it.)
After that I made a new project in TS and reloaded it with the base tune. Then installed the wideband and setting in TS but still the same.. the AFR just bounces a little just like it has no calibration ( just like the tps will until you calibrate it.)
Thread
Thread Starter
Forum
Replies
Last Post