WTS Engine w/FM II Hydra Complete.
#1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So WTS Compete Motor, Turbo System, Tranny, Rear End w/ Torsen II LSD.
99 Head,
Ported Polished
03 Block,
Bored 30 over, Honed, Balanced Internally
Mazdaspeed Thrust Bearings
Boundry Engineering Billet Oil pump gears,
Wisco 9:1 FM pistons,
Eagle H-rods,
Hydra EMS Stand Alone ,
GT-2860 Turbo
RC 550cc Injectors,
ACT Clutch,
HKS Bov,
HKS Internal Waste-gate,
PWR Radiator,
Precision Intercooler,
Racing Beat Full Cat Back exhaust,
AEM Wideband, AEM Tru-Boost.
Have Pictures of Engine Being Built and Video as well.
http://s1126.photobucket.com/albums/l618/jaredpmoser/
Also have Video of engine running.
$4,000 obo.
99 Head,
Ported Polished
03 Block,
Bored 30 over, Honed, Balanced Internally
Mazdaspeed Thrust Bearings
Boundry Engineering Billet Oil pump gears,
Wisco 9:1 FM pistons,
Eagle H-rods,
Hydra EMS Stand Alone ,
GT-2860 Turbo
RC 550cc Injectors,
ACT Clutch,
HKS Bov,
HKS Internal Waste-gate,
PWR Radiator,
Precision Intercooler,
Racing Beat Full Cat Back exhaust,
AEM Wideband, AEM Tru-Boost.
Have Pictures of Engine Being Built and Video as well.
http://s1126.photobucket.com/albums/l618/jaredpmoser/
Also have Video of engine running.
$4,000 obo.
Last edited by mach5; 02-28-2011 at 07:58 PM.
#3
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
would rather sell together it depends. What did you have in mind.
Last edited by mach5; 02-28-2011 at 07:22 PM.
#6
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Please check your inbox. Thanks.
#8
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Yes. Just trying to pay to finish my v8 swap. Bought everything pulling motor next week.
Wiring harness Wideband 02 for hydra has AC. Everything u can have rear axels if needed will not need them. Just want it all gone. I am really surprised how much and fast I am getting offers just put this up. Can ship anywhere as well the shop pulling ships JDM motors / trans and front clips all over US.
Wiring harness Wideband 02 for hydra has AC. Everything u can have rear axels if needed will not need them. Just want it all gone. I am really surprised how much and fast I am getting offers just put this up. Can ship anywhere as well the shop pulling ships JDM motors / trans and front clips all over US.
#11
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Interested in the Torsen with axles and drive shaft if you decide to part out.
#12
#13
#17
#19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Have you looked into shipping? I'm at 59057 zip code. How many miles were on the motor built (or hours if you just ran it and didn't drive) and did you properly break it in yet? Who did the machine work? What about the port work? And what sort of valve springs/valves are in there as well? Also, its got a MBSP right? Any crank scraper installed?
Pretty interested. I was going to build my own motor, but this will be close to the same damn price.
Pretty interested. I was going to build my own motor, but this will be close to the same damn price.