Moss MP62, Dual throttle, Intercooler, boost pulley upgrade, DIYPNP + Part out
#1
Thread Starter
Junior Member
iTrader: (1)
Joined: May 2011
Posts: 95
Total Cats: 3
From: South Jersey
Moss MP62, Dual throttle, Intercooler, boost pulley upgrade, DIYPNP + Part out
Moss MP62, Dual throttle, Intercooler, boost pulley upgrade, DIYPNP + Part out
--------------------------------------------------------------------------------
Selling a Moss MP62 Supercharger, 62.5mm nose pulley (14PSI indicated) Dual Throttle body set up, ( with blow off / recirc valve,+adjustment springs)
Cxracing 11x11x3 in bar and plate intercooler(never installed)
Aluminum 2.5 In CX racing pipe kit, with 3 layer silicone connections)
rx-7 550CC injcors (flowed and cleaned less than a month ago at injector rehab ( 2 flowed 554, 2 flowed 662 cc)
DIYPNP Megasquirt with sequential Injection.
GM open element IAT sensor
Innovate MTX-L wideband ( calibrated to the MS)
AEM Digital Boost gauge
AEM Oil Pressure gauge
Bosch(?) Oil ressure sender with alarm 7psi Switch
DDM works 3 Gauge / single din radio surrond.
Flyin Miata resonated race pipe (Cat delete) - NEW
Complete Kit. Instant boost
Gator Back belt for SC with the small pulley. Belts for OEM S/C pulley (9psi)
This Kit on a 1995 ( different intercooler - was undersized) made about 220whp, 50% throttle @ 4000rpms was an instant 13 PSI. TBH, i never hit 100% throttle off the dyno, but, if trends are accurate, should hit 15-16PSI and btter than 220hp.
feels like you dropped a V6 into the car. S/C has 20k miles ( part of manifold has been clearenced for hood contact, bt it is the moss manifold)
DIYPNP is tuned pretty well, on a new car a few hours of auto tune, and dyno time to work on the timing would have ou running great. Includes the bluetooth dongle, plus Serial/usb cable. Set up for launch control and running 3.2.8 gslender, so ou can work in A/C idle up etc.
S/C is a kit for Intercooler will require you to drop/ angle the radiator, i've got some prelim brackets for that.
Also, It's got a cobalt exhaust, but I'd need your good condition OEM, or an extra 150 + shiping
I can Include a Kenwood KDC-x995 bluetooth radio, Alpine 4 chanel amp, with Polk 6.5 in components, alpine 4/3 chanel AMP, and Boss frog rear Subwoofer set up with wiring kit for $400. Fits great, sounds awesome.
Also have a rear parcel shelf with 2 6in free air subs mounted, no issues with roll bar, or top etc. $50 + your old shelf.
If you're local, can add a Hard dog hard core single diagonal roll bar (300
Ultrashield 17 in seat, miata hight harness openings (200) I/Oport seatback brace ($75)
Schroth Profie II asm (with DOT press to release buckle - street legal) with 6 point sub (nut) straps (4 years left FIA date) ($125 - no wrecks).
Super Charger set up
S/C Kit ($ 3400) includes pulleys, MS, injectors, intercooler, piping, DTB, gauges, gauge surround.
I'll get Pictures up soon,
But if you want all that, plus a 1995 with 157,xxx miles, FM frame rails, moss oil cooler with remote filter location, TRM motorsports wheels, and good tires, with a set of General ulramax winter tires on steelies, and one hell of an impressive MX history (2 in thick folder, all oil changes, shocks, driveshaft etc, with spare tombstone, and center console, Very clean, almost no rust.
$7000 takes the whole set up.
Pictures soon to follow.
Jared. PM here, or jgumpert27 at gmal
--------------------------------------------------------------------------------
Selling a Moss MP62 Supercharger, 62.5mm nose pulley (14PSI indicated) Dual Throttle body set up, ( with blow off / recirc valve,+adjustment springs)
Cxracing 11x11x3 in bar and plate intercooler(never installed)
Aluminum 2.5 In CX racing pipe kit, with 3 layer silicone connections)
rx-7 550CC injcors (flowed and cleaned less than a month ago at injector rehab ( 2 flowed 554, 2 flowed 662 cc)
DIYPNP Megasquirt with sequential Injection.
GM open element IAT sensor
Innovate MTX-L wideband ( calibrated to the MS)
AEM Digital Boost gauge
AEM Oil Pressure gauge
Bosch(?) Oil ressure sender with alarm 7psi Switch
DDM works 3 Gauge / single din radio surrond.
Flyin Miata resonated race pipe (Cat delete) - NEW
Complete Kit. Instant boost
Gator Back belt for SC with the small pulley. Belts for OEM S/C pulley (9psi)
This Kit on a 1995 ( different intercooler - was undersized) made about 220whp, 50% throttle @ 4000rpms was an instant 13 PSI. TBH, i never hit 100% throttle off the dyno, but, if trends are accurate, should hit 15-16PSI and btter than 220hp.
feels like you dropped a V6 into the car. S/C has 20k miles ( part of manifold has been clearenced for hood contact, bt it is the moss manifold)
DIYPNP is tuned pretty well, on a new car a few hours of auto tune, and dyno time to work on the timing would have ou running great. Includes the bluetooth dongle, plus Serial/usb cable. Set up for launch control and running 3.2.8 gslender, so ou can work in A/C idle up etc.
S/C is a kit for Intercooler will require you to drop/ angle the radiator, i've got some prelim brackets for that.
Also, It's got a cobalt exhaust, but I'd need your good condition OEM, or an extra 150 + shiping
I can Include a Kenwood KDC-x995 bluetooth radio, Alpine 4 chanel amp, with Polk 6.5 in components, alpine 4/3 chanel AMP, and Boss frog rear Subwoofer set up with wiring kit for $400. Fits great, sounds awesome.
Also have a rear parcel shelf with 2 6in free air subs mounted, no issues with roll bar, or top etc. $50 + your old shelf.
If you're local, can add a Hard dog hard core single diagonal roll bar (300
Ultrashield 17 in seat, miata hight harness openings (200) I/Oport seatback brace ($75)
Schroth Profie II asm (with DOT press to release buckle - street legal) with 6 point sub (nut) straps (4 years left FIA date) ($125 - no wrecks).
Super Charger set up
S/C Kit ($ 3400) includes pulleys, MS, injectors, intercooler, piping, DTB, gauges, gauge surround.
I'll get Pictures up soon,
But if you want all that, plus a 1995 with 157,xxx miles, FM frame rails, moss oil cooler with remote filter location, TRM motorsports wheels, and good tires, with a set of General ulramax winter tires on steelies, and one hell of an impressive MX history (2 in thick folder, all oil changes, shocks, driveshaft etc, with spare tombstone, and center console, Very clean, almost no rust.
$7000 takes the whole set up.
Pictures soon to follow.
Jared. PM here, or jgumpert27 at gmal
#2
Thread Starter
Junior Member
iTrader: (1)
Joined: May 2011
Posts: 95
Total Cats: 3
From: South Jersey
* you will have to cut/ fit the intersooler piping. Never got around to putting that in.
Buying an STI, and a New house ( just had twins 6 months ago, and they don't fit in the miata trunk anymore)
also, new radiator, and all coolan hoses replaced last october. if you buy the car, all the oem parts removed for the SC ( maf, racing beat intake, intake tract, ECU, narrow band ecu, FM seal driver, and crank pulley tool, FM carbon fiber naca duct intake headlight cover, ) included. Timing belt and water belt done @ 152,000 miles (reciepts provided) Soft top in good shape, (window a bit hazy) and some TSW 16x8 rims with Goodyear sportpilot or something tires included ( 5/32 tread left)
TRM rims less than a year old, Dunlon Drizerras have 6/32nds left.
Buying an STI, and a New house ( just had twins 6 months ago, and they don't fit in the miata trunk anymore)
also, new radiator, and all coolan hoses replaced last october. if you buy the car, all the oem parts removed for the SC ( maf, racing beat intake, intake tract, ECU, narrow band ecu, FM seal driver, and crank pulley tool, FM carbon fiber naca duct intake headlight cover, ) included. Timing belt and water belt done @ 152,000 miles (reciepts provided) Soft top in good shape, (window a bit hazy) and some TSW 16x8 rims with Goodyear sportpilot or something tires included ( 5/32 tread left)
TRM rims less than a year old, Dunlon Drizerras have 6/32nds left.
#3
I might be interested in just the supercharger if you ever decide to sell it by it's self. I would only need the blower and the brackets to bolt it to the head. If become interested in letting that go separate let me know.
#8
Let's keep it to one thread please. Locking this one up.
https://www.miataturbo.net/miata-par...-pulley-72538/
C
https://www.miataturbo.net/miata-par...-pulley-72538/
C
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
Frank_and_Beans
Supercharger Discussion
13
09-12-2016 08:17 PM