Garret T28 (2560) turbo, NEW ARTech manifold + downpipe, CXRacing intercooler kit,etc
#1
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2012
Location: San Rafael, CA
Posts: 74
Total Cats: 2
Garret T28 (2560) turbo, NEW ARTech manifold + downpipe, CXRacing intercooler kit,etc
Hi All,
Got a bunch of parts for sale. Had been collecting them but decided to go another route.
-Garret T28 ball bearing turbo (2560) serial number 14411-69F00, 466541-1. Spins freely, no damaged blades. Minimal shaft play (moves a hair when push/pulled). Has a divider wall welded on the exhaust side (similar to the s15 spec R) by a shop (clean welds, good penetration). Also has a fairly new Garrett adjustable actuator (7-11 psi) installed which is $91.50 on bell engineering's website.
Will come with brand new oil feed line as well as a new oil drain fitting with barb end (not pictured). Water lines not included (sold already). SOLD
-New ARTech T25/T28 turbo manifold (fits 1.6) and ARTech seperated gas downpipe. Custom made, beefy, stainless steel, work of art. Need I say more? $850 shipped
-New CXRacing intercooler kit with piping, blow off valve, etc. SOLD
-Megasquirt 1 (with harness wired up to run parallel with stock ECU) PCB2.2, MSV30. I bought this used a year or two ago locally. I was told it works and it was meant for the 1.6 (90-93) but I cannot confirm this nor guarantee this as I have not run this in my car (I don't have IAT hooked up, VTPS, etc). I do not have a cable too hook it up to the computer either db9 to USB). It will also come with a megastim and a few 9 volt batteries so you can test the functions. SOLD
Extras I have for sale:
-OEM strut bar (came off a 99 miata). Fits NA's as well (1990-1998). SOLD
-OEM steering wheel with air bag (off my 92). $10 obo
-Manual boost controller $10 obo
-Billet Aluminum blow off valve (used). Looks very well built, comes with attachment to either vent-to-atmosphere or recirculate. Has built in check valve which can be removed.I have the flange but it is welded on a pipe that was used on a Volvo S70 (I can cut off the section where the flange is before I ship it out or sent it out whole). $40 obo
-Four 3rd Gen Eclipse vents (louver type). Fits perfectly into NB's, requires some modification (shaving) for the NA eyeball vents. Great upgrade and/or replace sagging eyeball vents. You can close off vents not in use. 1 of them isfixed with a dab of JB weld where it attaches (you can't see it really). $25 obo (they sell for $10 each on ebay)
Located in the bay area (California). Can also take additional pictures if needed. Email me at solomon.h.young@gmail.com for a quicker response.
Got a bunch of parts for sale. Had been collecting them but decided to go another route.
-Garret T28 ball bearing turbo (2560) serial number 14411-69F00, 466541-1. Spins freely, no damaged blades. Minimal shaft play (moves a hair when push/pulled). Has a divider wall welded on the exhaust side (similar to the s15 spec R) by a shop (clean welds, good penetration). Also has a fairly new Garrett adjustable actuator (7-11 psi) installed which is $91.50 on bell engineering's website.
Will come with brand new oil feed line as well as a new oil drain fitting with barb end (not pictured). Water lines not included (sold already). SOLD
-New ARTech T25/T28 turbo manifold (fits 1.6) and ARTech seperated gas downpipe. Custom made, beefy, stainless steel, work of art. Need I say more? $850 shipped
-New CXRacing intercooler kit with piping, blow off valve, etc. SOLD
-Megasquirt 1 (with harness wired up to run parallel with stock ECU) PCB2.2, MSV30. I bought this used a year or two ago locally. I was told it works and it was meant for the 1.6 (90-93) but I cannot confirm this nor guarantee this as I have not run this in my car (I don't have IAT hooked up, VTPS, etc). I do not have a cable too hook it up to the computer either db9 to USB). It will also come with a megastim and a few 9 volt batteries so you can test the functions. SOLD
Extras I have for sale:
-OEM strut bar (came off a 99 miata). Fits NA's as well (1990-1998). SOLD
-OEM steering wheel with air bag (off my 92). $10 obo
-Manual boost controller $10 obo
-Billet Aluminum blow off valve (used). Looks very well built, comes with attachment to either vent-to-atmosphere or recirculate. Has built in check valve which can be removed.I have the flange but it is welded on a pipe that was used on a Volvo S70 (I can cut off the section where the flange is before I ship it out or sent it out whole). $40 obo
-Four 3rd Gen Eclipse vents (louver type). Fits perfectly into NB's, requires some modification (shaving) for the NA eyeball vents. Great upgrade and/or replace sagging eyeball vents. You can close off vents not in use. 1 of them isfixed with a dab of JB weld where it attaches (you can't see it really). $25 obo (they sell for $10 each on ebay)
Located in the bay area (California). Can also take additional pictures if needed. Email me at solomon.h.young@gmail.com for a quicker response.
Last edited by Solomon; 07-21-2014 at 01:49 AM. Reason: Priced lowered!
#4
I'm interested in the water lines and fittings. Price shipped to 92691?
#5
interested in the whole ic set. price shipped to 94080?
#6
cant PM due to limited posts... if you'll do $60 shipped for strut bar ill take it! Or PM me your best price, thanks!
#10
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2012
Location: San Rafael, CA
Posts: 74
Total Cats: 2
Turbo is still for sale. If you don't need the oil feed and drain fitting I'll reduce the price a little bit.
Thanks for commenting on the MS1. I'll update the original post but to clarify it's for the 1.6 (90-93).
#12
compatibility 1.8 nb2 01'?
#13
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2012
Location: San Rafael, CA
Posts: 74
Total Cats: 2
The manifold will not fit the 1.8 (only 1.6). The downpipe should be able to fit either or as long as it's mated to a T25 or T28. Also depends on where the turbo is mounted (in relation to the manifold)
Updates:
Turbo is SOLD.
MS1 is SOLD.
Both manifold and downpipe are still available (new, unused). Had a few questions regarding the diameter of the DP. It's 2.5" and has an oxygen bung already welded on it in case you couldn't see in the picture.
Updates:
Turbo is SOLD.
MS1 is SOLD.
Both manifold and downpipe are still available (new, unused). Had a few questions regarding the diameter of the DP. It's 2.5" and has an oxygen bung already welded on it in case you couldn't see in the picture.
Last edited by Solomon; 07-20-2014 at 02:09 AM.
#14
im mike who picked up the ms...nice to meet you today and thanks for the ride and info! glws on your other stuff!
#16
Thread
Thread Starter
Forum
Replies
Last Post
elesjuan
Build Threads
7
11-03-2015 01:51 PM