Full Turbo Kit for 1.8 Na
#1
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2007
Location: Santa Clarita, CA
Posts: 158
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Selling this from my 95 with AC, Cruise Control and Power Steering. PNP for 94/95.
Downpipe was repaired(when I bought it there was a pin sized hole and the metal looked thin) and doesn't look the prettiest but is fully functional.
I was unlucky and after using this on my miata for about a month (this car isn't my DD and I probably only drove it 10-15 times with the turbo) I was pulled over for no front plate and given a state ref ticket for the turbo (just before I received my carb sticker).
I had to remove the turbo system and go back to na.
This kit is everything u need to run up to about 220whp depending on your tune. You will need to buy new studs and nuts for the connections to the turbo (mani-turbo-DP). I will include the hoses I used for coolant feed/return.
This thing spooled instantly for me. It was unreal.
Garrett's GT2554Clocked for IC(3000 miles on turbo)
Begi's/FM exhaust manifold (No EGR but I will include the block off plate)
FM/Begi Downpipe(older style)
MSPNP for 95, road tuned at about 6psi(GM boost control and IAT for MAF Delete)
440 injectors(pnp with MS), cleaned before I used them(need a set of gaskets which should always be replaced when removed anyway)
Enthuza Budget Turbo Racer 2.5" cat-back
SS oil feed/Oil drain(for the oil pan just drill hole, screw fitting in, and JB weld it to the pan for a perfect seal)
Innovate LC-1 controller and sensor with all wiring
FMIC -fit with trimming of the undertray and removal of air splitter/diverter thing. I used a bit of ABS sheet I had. The hotside is a silicone Flyin' Miata pipe, coldside is Bell's piece off of the intake mani down to 2.5" pipes and couplers Forge BOV.
Intake is a little ghetto but works.(silicone tube with VC breather tube hole and a filter on the end. very easy to fab your own if you want)
Begi's Turbo Heatsheild(never used)
Looking to get $2200 and I would obviously prefer to sell locally(southern california-ish). I guess I will ship but at the buyers expense. Not parting this unless there is a buyer for all parts.
There are many compatible parts with this if upgrades are wanted in the future(Intake, DP, Mani, etc.). It's basically a FM or Begi kit with some homebrew touches.
BTW Disclaimer I do have a BEGI CARB sticker also but should not be used unless the kit is used in accordance to their rules
(EGR drilled and fitted to mani, Stock injectors, Bandaids or piggyback) I have bandaids for sale(minus walbro) and I will post them in another thread, as well as a 6 puck sprung ACT clutch disk.(PS also posting this on another forum as ilovecurves)
Now for pics...
Downpipe was repaired(when I bought it there was a pin sized hole and the metal looked thin) and doesn't look the prettiest but is fully functional.
I was unlucky and after using this on my miata for about a month (this car isn't my DD and I probably only drove it 10-15 times with the turbo) I was pulled over for no front plate and given a state ref ticket for the turbo (just before I received my carb sticker).
![Jerkit](https://www.miataturbo.net/images/smilies/jerkit.gif)
This kit is everything u need to run up to about 220whp depending on your tune. You will need to buy new studs and nuts for the connections to the turbo (mani-turbo-DP). I will include the hoses I used for coolant feed/return.
This thing spooled instantly for me. It was unreal.
Garrett's GT2554Clocked for IC(3000 miles on turbo)
Begi's/FM exhaust manifold (No EGR but I will include the block off plate)
FM/Begi Downpipe(older style)
MSPNP for 95, road tuned at about 6psi(GM boost control and IAT for MAF Delete)
440 injectors(pnp with MS), cleaned before I used them(need a set of gaskets which should always be replaced when removed anyway)
Enthuza Budget Turbo Racer 2.5" cat-back
SS oil feed/Oil drain(for the oil pan just drill hole, screw fitting in, and JB weld it to the pan for a perfect seal)
Innovate LC-1 controller and sensor with all wiring
FMIC -fit with trimming of the undertray and removal of air splitter/diverter thing. I used a bit of ABS sheet I had. The hotside is a silicone Flyin' Miata pipe, coldside is Bell's piece off of the intake mani down to 2.5" pipes and couplers Forge BOV.
Intake is a little ghetto but works.(silicone tube with VC breather tube hole and a filter on the end. very easy to fab your own if you want)
Begi's Turbo Heatsheild(never used)
Looking to get $2200 and I would obviously prefer to sell locally(southern california-ish). I guess I will ship but at the buyers expense. Not parting this unless there is a buyer for all parts.
There are many compatible parts with this if upgrades are wanted in the future(Intake, DP, Mani, etc.). It's basically a FM or Begi kit with some homebrew touches.
BTW Disclaimer I do have a BEGI CARB sticker also but should not be used unless the kit is used in accordance to their rules
![no no](https://www.miataturbo.net/images/smilies/nono.gif)
Now for pics...
Last edited by Chapman; 11-02-2009 at 05:45 PM.
#2
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2007
Location: Santa Clarita, CA
Posts: 158
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I haven't snapped a pic of the cat-back yet but I can if needed.
![Name: DSC01924.jpg
Views: 166
Size: 255.8 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202816d1501246594-full-turbo-kit-1-8-na-dsc01924.jpg)
gt2554
![Name: DSC01930.jpg
Views: 148
Size: 316.5 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202817d1501246594-full-turbo-kit-1-8-na-dsc01930.jpg)
Downpipe(bottom half included obviously but not pictured)
![Name: DSC01931.jpg
Views: 138
Size: 259.7 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202818d1501246594-full-turbo-kit-1-8-na-dsc01931.jpg)
Exhaust Manifold(looks like **** but clean up is easy with BBQ paint + Heatshield covering it.)
![Name: DSC01967.jpg
Views: 117
Size: 185.8 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202819d1501246594-full-turbo-kit-1-8-na-dsc01967.jpg)
MSPNP with injectors(440's are included and 460's pictured too)
![Name: DSC01958.jpg
Views: 115
Size: 308.9 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202820d1501246594-full-turbo-kit-1-8-na-dsc01958.jpg)
Intercooler, Intake, BOV setup
![Name: DSC01962.jpg
Views: 105
Size: 377.1 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202821d1501246594-full-turbo-kit-1-8-na-dsc01962.jpg)
Oil feed/drain, coolant lines, magnacore wires,
![Name: DSC01965.jpg
Views: 70
Size: 331.0 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202822d1501246594-full-turbo-kit-1-8-na-dsc01965.jpg)
Heat shield
![Name: DSC01923.jpg
Views: 72
Size: 173.4 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202823d1501246594-full-turbo-kit-1-8-na-dsc01923.jpg)
Random pics of IC fitting
![Name: 76971925.jpg
Views: 95
Size: 66.1 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202824d1501246594-full-turbo-kit-1-8-na-76971925.jpg)
![Name: DSC01924.jpg
Views: 166
Size: 255.8 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202816d1501246594-full-turbo-kit-1-8-na-dsc01924.jpg)
gt2554
![Name: DSC01930.jpg
Views: 148
Size: 316.5 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202817d1501246594-full-turbo-kit-1-8-na-dsc01930.jpg)
Downpipe(bottom half included obviously but not pictured)
![Name: DSC01931.jpg
Views: 138
Size: 259.7 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202818d1501246594-full-turbo-kit-1-8-na-dsc01931.jpg)
Exhaust Manifold(looks like **** but clean up is easy with BBQ paint + Heatshield covering it.)
![Name: DSC01967.jpg
Views: 117
Size: 185.8 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202819d1501246594-full-turbo-kit-1-8-na-dsc01967.jpg)
MSPNP with injectors(440's are included and 460's pictured too)
![Name: DSC01958.jpg
Views: 115
Size: 308.9 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202820d1501246594-full-turbo-kit-1-8-na-dsc01958.jpg)
Intercooler, Intake, BOV setup
![Name: DSC01962.jpg
Views: 105
Size: 377.1 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202821d1501246594-full-turbo-kit-1-8-na-dsc01962.jpg)
Oil feed/drain, coolant lines, magnacore wires,
![Name: DSC01965.jpg
Views: 70
Size: 331.0 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202822d1501246594-full-turbo-kit-1-8-na-dsc01965.jpg)
Heat shield
![Name: DSC01923.jpg
Views: 72
Size: 173.4 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202823d1501246594-full-turbo-kit-1-8-na-dsc01923.jpg)
Random pics of IC fitting
![Name: 76971925.jpg
Views: 95
Size: 66.1 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202824d1501246594-full-turbo-kit-1-8-na-76971925.jpg)
![Name: 37aff5ab.jpg
Views: 49
Size: 44.5 KB](https://www.miataturbo.net/attachments/miata-parts-sale-trade-5/202825d1501246594-full-turbo-kit-1-8-na-37aff5ab.jpg)
#10
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Interested in MSPNP, Innovate LC-1 and Heatshield!
#11
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2007
Location: Santa Clarita, CA
Posts: 158
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I may be parting this out guys. Lemme put some #'s together and I'll pm u guys. If you want dibs on stuff the thread is where to do it(don't pm). That way it's obvious to everyone who calls for what.
Gimme a day or so to put this together.
Also, Sorry for the Bandwidth Fail guys
Gimme a day or so to put this together.
Also, Sorry for the Bandwidth Fail guys
![Giggle](https://www.miataturbo.net/images/smilies/gay.gif)
#12
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
paycheck is in, so is it still for sale?
I'm still interested in MSPNP, Innovate LC-1, Heatshield and ic (piping)
cheerz,
Rt
I'm still interested in MSPNP, Innovate LC-1, Heatshield and ic (piping)
cheerz,
Rt
#14
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
2nd dibs on exhaust, pm me price pelase thanks
#15
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2007
Location: Santa Clarita, CA
Posts: 158
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
ok guys pics are working again... New plans. I'm keeping the MSPNP and LC-1
$1850 for the rest of this stuff plus shipping OBO. I really want to sell it together. If you want to make an offer for something PM me.
I wouldn't mind selling the exhaust by itself, but I would really prefer to sell turbo, mani, dp, and ic together because they all work together.
Plus New ACT 6-puck sprung clutch disc for sale $90 shipped***SOLD***
Bipes unit $130 shipped
FPR $30 +shipping
O2 clamp $55 shipped
$1850 for the rest of this stuff plus shipping OBO. I really want to sell it together. If you want to make an offer for something PM me.
I wouldn't mind selling the exhaust by itself, but I would really prefer to sell turbo, mani, dp, and ic together because they all work together.
Plus New ACT 6-puck sprung clutch disc for sale $90 shipped***SOLD***
Bipes unit $130 shipped
FPR $30 +shipping
O2 clamp $55 shipped
Last edited by Chapman; 12-04-2009 at 09:15 PM.
#18
Junior Member
Thread Starter
iTrader: (2)
Join Date: Feb 2007
Location: Santa Clarita, CA
Posts: 158
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I want to change the price to $1700. I want this stuff gone. It's a great deal for this stuff. I paid a lot more for this stuff
. For everything listed in my first post except for the MSPNP and the lc-1.
![facepalm](https://www.miataturbo.net/images/smilies/facepalm.gif)
#19
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Do u still have the bipes, fpr and 02 clamp for sale? If so is the fpr a Begi? Any pics? U can email me at mshorty6686@aol.com or pm me here.
Sorry i'm unable to PM since I don't have enough posts.
I perfer to search for my info instead of posting retorical questions.
Sorry i'm unable to PM since I don't have enough posts.
I perfer to search for my info instead of posting retorical questions.
Thread
Thread Starter
Forum
Replies
Last Post
Andifer
Miata parts for sale/trade
8
09-23-2015 05:43 PM