FS: Fully Built Turbo 1.9L w/ GT3076R + RX7 TII Trans + More
#1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Hey guys,
I bought this setup from Danny George and due to somethings coming up I won't be swapping it into the car I intended and I am considering selling it..
1.9L BP Engine
Garage AutoHero Built
RX7 TII - 5 Speed Transmission, Adapter Plate, & Aluminum Driveshaft (For use with TII Rear End)
M-Tuned/Eagle H Beam Rods
Wiseco 9:1 Pistons 1mm Overbore
ACL Race Bearings
ARP Main & Head Stud Hardware
Boundary Engineering Billet High Flow Oil Pump
Supertech Springs & Titanium Retainers
99’ Spec Head - Mild Port and Polish
Fidanza Adjustable Cam Gears
Clutchnet 6 Puck Clutch (barely broken in) Spare 4 Puck Clutch Also Included
Alum Fidanza Flywheel
Custom Coolant Reroute
Begi Intake Manifold + 70mm Throttle Body
Eagle Vacuum Manifold
Custom Flipside Ramhorn Manifold, Garrett GT3076R, Tial Wastegate (All Heat Coated)
3" Downpipe & Exhaust
Greddy Type S BOV
Precision Intercooler
2.5” Intercooler Piping
Vishnu Dual Feed Fuel Rail + Lines
Precision 720CC Injectors
Toyota Coil On Plug Conversion
Fuse Panel and Starter
AEM EMS ECU
AiM’s Digital Cluster - PNP With Harness
Custom Wiring Harness - Complete Chassis Formula Drift Spec w/Ignition Button and push fuses.
Under 10k milage on the motor. All hot components (manifold, turbo, waste gate) are all coated to 2000degrees.
Willing to sell the entire long block w/o manifolds or entire setup all as one.
Made 390whp/300tq at 14psi on current tune. Tune on ECU is good to 22psi waste gate spring just needs to be changed and you've got 500whp.
Original thread from when I bought it from Danny:
ClubRoadster.net
$7000.
I am considering parting it out or selling without electronics. If you are interested in any of the components please feel free to PM me or post here. Looking to figure this out ASAP.
I bought this setup from Danny George and due to somethings coming up I won't be swapping it into the car I intended and I am considering selling it..
1.9L BP Engine
Garage AutoHero Built
RX7 TII - 5 Speed Transmission, Adapter Plate, & Aluminum Driveshaft (For use with TII Rear End)
M-Tuned/Eagle H Beam Rods
Wiseco 9:1 Pistons 1mm Overbore
ACL Race Bearings
ARP Main & Head Stud Hardware
Boundary Engineering Billet High Flow Oil Pump
Supertech Springs & Titanium Retainers
99’ Spec Head - Mild Port and Polish
Fidanza Adjustable Cam Gears
Clutchnet 6 Puck Clutch (barely broken in) Spare 4 Puck Clutch Also Included
Alum Fidanza Flywheel
Custom Coolant Reroute
Begi Intake Manifold + 70mm Throttle Body
Eagle Vacuum Manifold
Custom Flipside Ramhorn Manifold, Garrett GT3076R, Tial Wastegate (All Heat Coated)
3" Downpipe & Exhaust
Greddy Type S BOV
Precision Intercooler
2.5” Intercooler Piping
Vishnu Dual Feed Fuel Rail + Lines
Precision 720CC Injectors
Toyota Coil On Plug Conversion
Fuse Panel and Starter
AEM EMS ECU
AiM’s Digital Cluster - PNP With Harness
Custom Wiring Harness - Complete Chassis Formula Drift Spec w/Ignition Button and push fuses.
Under 10k milage on the motor. All hot components (manifold, turbo, waste gate) are all coated to 2000degrees.
Willing to sell the entire long block w/o manifolds or entire setup all as one.
Made 390whp/300tq at 14psi on current tune. Tune on ECU is good to 22psi waste gate spring just needs to be changed and you've got 500whp.
Original thread from when I bought it from Danny:
ClubRoadster.net
$7000.
I am considering parting it out or selling without electronics. If you are interested in any of the components please feel free to PM me or post here. Looking to figure this out ASAP.
Last edited by mikeboldt; 02-17-2014 at 04:03 PM.
#2
#3
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Hmm I'm about to be building my motor but maybe this is the way to go.
Price on everything minus
Ecu, wiring, coils, alt, intercooler or piping...
Or just the motor, including turbo and intake
Or minus turbo and mani
Price on everything minus
Ecu, wiring, coils, alt, intercooler or piping...
Or just the motor, including turbo and intake
Or minus turbo and mani
#4
#5
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I have someone who wants just the long block, no manifolds, electronics, etc.
Open to offers on other stuff, including transmission setup, manifold/turbo/wastegate/screamer/downpipe, Intake Manifold w/ TB... Let me know!
Open to offers on other stuff, including transmission setup, manifold/turbo/wastegate/screamer/downpipe, Intake Manifold w/ TB... Let me know!
#7
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I contacted AEM regarding the EMS. It's for a 90-95 generation Miata. Danny was able to run it with the harness because it's a full chassis custom wiring setup, he had it in an NA. I should mention the harness has a AEM Air Fuel gauge on it as well.
I was planning to swap it all into my 97 and using the motor portion of Danny's wiring harness while retaining my stock wiring for the body harness.
I have an offer for $650 for the cluster, $650 for the ECU. No clue what would be fair for the wiring harness.
I was planning to swap it all into my 97 and using the motor portion of Danny's wiring harness while retaining my stock wiring for the body harness.
I have an offer for $650 for the cluster, $650 for the ECU. No clue what would be fair for the wiring harness.
#8
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Only if you posted this two months earlier i would have bought it instantly
#9
#10
#11
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Vishnu dual fuel rail & lines.
Available?
Available?
#12
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I'm unable to pm you due to my number of posts. Can you email me at:
Pperez@reliablebusiness.net
Thnx,
Pete
Pperez@reliablebusiness.net
Thnx,
Pete
#13
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
anyone buy just motor yet im interested
Thread
Thread Starter
Forum
Replies
Last Post