Hello My name is Ryan Kaufman and I am currently Selling a completely Rebuilt and Built 1999 1.8l Engine. Don't waste your time buying a used junkyard motor for 1200 - 1300 bucks with no guarantee....this is a Steal at 1800 bucks you cant even buy a factory rebuilt motor for this price!


0 miles brand new rebuilt never used and guaranteed to run

Specifications:

BLOCK IS STOCK 99 block

-Stock pistons and rods fully cleaned and re ringed

-Shimmed and cleaned oil pump

-block was hot tanked and rigorously cleaned along with the crank

-All bearings were replaced within the block

-Keyway is in perfect condition!

HEAD IS BUILT

-Completely rebuilt and shaved 1999 head

-Brand new Mazda Head gasket and waterpump and timing belt kit

***Supertech Valve Springs with titanium Retainers

***AEM Adjustable Cam Gears Intake and exhaust

***ARP HEAD STUDS



THE MOTOR WAS BUILT BY SEBASTIEN AT ANSA MOTORSPORTS

(A ferrari, kit car, and lemans race team and shop in miami)



EVERY OIL SEAL AND WATER SEAL WAS REPLACED



Complete Photos are here

1999 miata motor fs pictures by gdnimr0d - Photobucket



comes complete with the 1999 miata valve cover with brand new gasket

This motor can be used in these year miatas from 1994-2000 or any 1.8 swapped 90-93...to use the motor in the 99-00 setup only the intake aem cam gear will have to be swapped with a factory one due to the cam angle sensor setup on the 99 and 00.

I personally guarantee the motor to run with no issues with a 60 warranty as long as its used for regular driving aplication.
IT DOES COME WITH A 99-00 INTAKE MANIFOLD FOR THAT PRICE



DONT PM ME OR EMAIL ME IF YOU ARE SERIOUS! THEN CALL ME!

CALL ME AT 754 244 1755 anytime anyday!

RYAN KAUFMAN

PRICE 1800 OBO

LOCATION IS IN FT LAUDERDALE FLORIDA

 

Not thread crapping, but just wondering - along with most of the other members here when they read this thread. Why did you go to all of that time and expense and not put in a $300 set of forged rods FTW???

 

This motor was built for as a spare competition drifting motor and was built on a budget the stock rods hold 12-13 psi no issue
thanks for the interest

 

seems like a nice clean engine. not too sure how many buyers you will find here because most of us are broke and would want upgraded pistons/rods anyways. i say you sell the head separately from the block.

 

Please tell me this engine was never lifted with a rope.

 

Rope = bad
Seatbelt FTW

 

the factory pistons and rods hold 12-13 psi nicely, i know from experience....15psi and over and good bye....
This motor is a perfect N/A build for higher rpms or for a mild turbo setup

I personally guarantee the motor to run with no issues with a 60 warranty as long as its used for regular driving aplication.
IT DOES COME WITH A 99-00 INTAKE MANIFOLD FOR THAT PRICE
thanks!

 

From which turbo? I bet a GT2860RS at 12psi would blow it up nicely.

 

Oh, I can think of at least a dozen turbos that will blow that up at 12lbs.

 

This guy is a good seller. I bought a car from him and know him from the FL drifting scene. He has been working on and building Miatas for several years now, when he says guarantee he means it, he has an Engineering degree and does this as a business. Also notice the price is obo.

Good Luck Ryan and you old daily is completely transformed now, coils, wheels, rollbar, and most important of all 5 speed swap.

 

I'm wrapping up an engineering degree (second degree)...and I'll tell you every day of the week that manifold pressure doesn't blow motors...peak cylinder pressure does, whether from knock, or a high volume flow rate turbo at what is otherwise a "reasonable" output pressure.

I trust the seller, but terminology is important.

If this motor had rods it would be on it's way to Texas already.

I'm interested...but for the way it's built I'd find myself close to dangerously high torque levels way too fast.

 

Its not like he stated this a built 500hp motor either. Had he added rods the price would probably directly reflect that. Not sure why I feel like I'm having to defend myself or him. He's basically offering a nicely rebuilt motor for much cheaper than the average person could have done.

 

thanks ^^^^
yeah sorry guys this will go on ebay soon so hopefully someone will get a nicely built motor
the 15 psi i ran on my stock motor was with a gt2560r and the motor never blew

althought shortly after a few events I pulled it apart and built it completely just to guarantee that i wasnt going to blow the motor, since then I now run 17 psi on carillo h beam rods and they havent given me an issue

 

I'll take the head if you'd ever decide to sell it in that fashion

 

shoot me an offer on it and we will see what happens

 

I might be keen on the full engine. Let me have your email so we can discuss, thank you.

 

sorry engine is sold

 

No worries mate, thanks for replying!

 

I was going to sell mine for the same price. It was built to oem specs though.

 

yeah fail^^^^ lol