90-93 megasquirt pnp, Cop kit, 460cc rx7 injectors
#1
Junior Member
Thread Starter
iTrader: (2)
Join Date: Oct 2013
Location: Arcade, New York
Posts: 157
Total Cats: -1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
First up the megasquirt diypnp is less then a month old and never been run. It's for the 1.6 and is setup for vtps and iat also has the wire installed (yellow wire coming out of the box) to hook directly to a wideband. Everything else is set for stock. It has the newest firmware loaded and the tune for the stock injectors. It will come with 12volt ac plug to tune out of the car. Also the USB serial hub and tuning cable. I used silver solder and have 10-12 hours into it but I am OCD when it comes to electronics. I have roughly $500 invested not including time and 2 tubes of solder at 18 bucks a tube. Asking $600 obo. Also includes all left over parts that are not used on the build see pictures
Next is my Toyota denso cop kit. This is a pnp kit I put together myself. I made the harness to just plug into the stock igniter harness. The coils are oem denso's and cost my $70 a piece. I also made the bracket out of thick aluminum stock and it uses the top 3 valve cover bolts to hold it down. This is also new and never used. Asking $250 obo.
Last are my rx7 460cc redtop injectors. These are high impedance and can be used as pnp but you need to install the supplied pigtails in place of your stock injector harness clips. Pigtails included. These were cleaned at a local shop but I lost the flow chart. They also replaced all rubber O-rings, pintle caps and the small screens on the top of the injectors. I never used these either and are used but recently rebuilt and cleaned. Asking $200 obo
Please text for faster response 716-361-3604. All prices are shipped
Next is my Toyota denso cop kit. This is a pnp kit I put together myself. I made the harness to just plug into the stock igniter harness. The coils are oem denso's and cost my $70 a piece. I also made the bracket out of thick aluminum stock and it uses the top 3 valve cover bolts to hold it down. This is also new and never used. Asking $250 obo.
Last are my rx7 460cc redtop injectors. These are high impedance and can be used as pnp but you need to install the supplied pigtails in place of your stock injector harness clips. Pigtails included. These were cleaned at a local shop but I lost the flow chart. They also replaced all rubber O-rings, pintle caps and the small screens on the top of the injectors. I never used these either and are used but recently rebuilt and cleaned. Asking $200 obo
Please text for faster response 716-361-3604. All prices are shipped
Last edited by Miatacrazy716; 10-31-2014 at 07:59 PM. Reason: changed title to aid sales
#7
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I thought the rx7 460cc injectors could be plugged into with the factory clips?
They should be according to:
http://miataturbo.wikidot.com/fuel-injectors
Because they are a "F" connector like the factory injectors, according to the site and pictures of both certainly favors that conclusion.
![Dunno](https://www.miataturbo.net/images/smilies/dunno.gif)
http://miataturbo.wikidot.com/fuel-injectors
Because they are a "F" connector like the factory injectors, according to the site and pictures of both certainly favors that conclusion.
#8
Junior Member
Thread Starter
iTrader: (2)
Join Date: Oct 2013
Location: Arcade, New York
Posts: 157
Total Cats: -1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
There was a year that they used this style clip. Don't remember the full story as I bought these over a year ago and did the research then but at some point they used the dsm style connector then switched. Believe me these are high impedance injectors. I ohm tested them when I got them to make sure I didn't get screwed when I bought these. If you don't believe me there is a few topics like this on here in the forum to back me up. Your not the first to ask me this and probably not the last.
Thread
Thread Starter
Forum
Replies
Last Post