1.6 COPs hold down brackets only $40 shipped
#21
2 Props,3 Dildos,& 1 Cat
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
note to whoever makes their own connector harness: you'll probably want to dremel a little bit of pin material off so the pins actually lock into the toyota connector housings. I noticed theres about 60-70 thou too much material on the top portion of the pin to lock in place. ummm i'll reply with a badly drawn diagram.
#23
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,607
Total Cats: 4,102
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
that's good to know. only two of mine pulled out ever....so I filled the connector with blue siliconed from behind and used super glue. Never had a real problem with them. Also helped make it more weatherproof.
I still have plenty of these pins leftover! like 366 to be exact.
I still have plenty of these pins leftover! like 366 to be exact.
#30
Supporting Vendor
![](/mt2011/images_td/ranks/vendor.png)
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
m@ I'm sure the lock tab will hold the pins in fine. But since I'm making stuff to send out, I want it to be bulletproof. I was planning on wrapping some electrical tape around the wiring at the connector and filling with epoxy. that would not only bond everything in place, but would also create a weather seal. and also if one wire got pulled, it would spread the load across all 4. kind of a ghetto strain relief.
paul, no rush dude. I have several 1.6 harness to make. thanks though.
paul, no rush dude. I have several 1.6 harness to make. thanks though.
#32
Elite Member
iTrader: (11)
Join Date: Jun 2007
Location: Overland Park, Kansas
Posts: 5,360
Total Cats: 43
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I'd be interested in a mounting plate for the 1.8 COPs.. once I can get a set of coils scrounged up. Still working on that one.
Uhm, I might add that I'm not running a Miata cam cover, but it should fit all the same between miata and 323/Protoge/Escort covers I would think.
Uhm, I might add that I'm not running a Miata cam cover, but it should fit all the same between miata and 323/Protoge/Escort covers I would think.
#33
2 Props,3 Dildos,& 1 Cat
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 573
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I'd be interested in a mounting plate for the 1.8 COPs.. once I can get a set of coils scrounged up. Still working on that one.
Uhm, I might add that I'm not running a Miata cam cover, but it should fit all the same between miata and 323/Protoge/Escort covers I would think.
Uhm, I might add that I'm not running a Miata cam cover, but it should fit all the same between miata and 323/Protoge/Escort covers I would think.
#34
Elite Member
iTrader: (11)
Join Date: Jun 2007
Location: Overland Park, Kansas
Posts: 5,360
Total Cats: 43
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
![](https://www.miataturbo.net/images/smilies/mad.gif)
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
chris101
Miata parts for sale/trade
5
02-19-2016 07:13 PM
chris101
Miata parts for sale/trade
2
10-09-2015 09:08 AM