MS3X-1.6 Sync loss @ 4K, high idle
#43
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
here, i have my 2nd trigger jumper going to iac1a for all my non-expansion installs. so i use a jumper from iac1a to pin32 (cam in) of the expander to bring the cam signal in when using the stim.
![](https://www.miataturbo.net/attachments/megasquirt-18/66466-ms3x-1-6-sync-loss-%40-4k-high-idle-img_20130203_140220.jpg?dateline=1359918223)
#45
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
you just need the one.
those were useful back in to day for ms1 and ms2 installs where I could test outputs, I've just never removed them; I suppose I should.
Since everything is running off the ms3x card they are useless, and I need this: JimStimX Expansion Board - Assembled DIYAutoTune.com
those were useful back in to day for ms1 and ms2 installs where I could test outputs, I've just never removed them; I suppose I should.
Since everything is running off the ms3x card they are useless, and I need this: JimStimX Expansion Board - Assembled DIYAutoTune.com
#46
Junior Member
Thread Starter
Join Date: May 2011
Location: Central Kentucky
Posts: 221
Total Cats: 1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Oh ok then hah. I haven't had a chance to test it yet due to school. But I ordered another pot from diy. Hopefully I can get around to messing with it tomorrow and have it going by weekend.
#48
Junior Member
Thread Starter
Join Date: May 2011
Location: Central Kentucky
Posts: 221
Total Cats: 1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
New pot R56 installed and it's still doing the same. Full counter clockwise, I'm geting .04v across the resistor. and 6-7 turns, I'm getting .09v What is going on here? Am I'm measuring the right place?
![](https://www.miataturbo.net/attachments/megasquirt-18/66980-ms3x-1-6-sync-loss-%40-4k-high-idle-20130208_003409_zps74eb2297-1.jpg?dateline=1360302139)
#51
Junior Member
Thread Starter
Join Date: May 2011
Location: Central Kentucky
Posts: 221
Total Cats: 1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Didn't have a lot of time today, but it seemed to have fixed the sync loss issue. Which I'm super pumped about. I still cant get the idle sorted out without it hunting, and it still has fluttery RPM deceleration.
#57
Junior Member
Thread Starter
Join Date: May 2011
Location: Central Kentucky
Posts: 221
Total Cats: 1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Flashed the firmware this morning, fixed the WUE, and now the thing is running amazing! I been driving and tuning all day and I'm so excited that it is running so well now. It is getting poopy gas mileage though
Is the middle red LED supposed to stay on? Mine is on sometimes, sometimes never lights up, and sometimes flashes
Is the middle red LED supposed to stay on? Mine is on sometimes, sometimes never lights up, and sometimes flashes
#58
Elite Member
iTrader: (1)
Join Date: Jun 2006
Location: Warrington/Birmingham
Posts: 2,642
Total Cats: 42
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Flashed the firmware this morning, fixed the WUE, and now the thing is running amazing! I been driving and tuning all day and I'm so excited that it is running so well now. It is getting poopy gas mileage though
Is the middle red LED supposed to stay on? Mine is on sometimes, sometimes never lights up, and sometimes flashes
Is the middle red LED supposed to stay on? Mine is on sometimes, sometimes never lights up, and sometimes flashes
I.e. when it's on you're in WUE