Lost on getting my car started. 1.6 M45 w/ MS
#21
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Ok, update from this evening.
Got the AIT sensor wired correctly, connected the fuel pump relay wires (Runs when in On position) and downloaded the provided .inc files. AIT sensor is reading correctly now in Tunerstudio.
Since I got straightened out, I tried starting the car again. No luck. Got the car to crank over nicely and sputter trying to start but could not keep going. Was following the directions per various sources where you are trying to set the timing.
Ended up messing around with the timing trigger angle, CAS position, cranking and after enrichment pulse widths. Seemed to be getting closer but no cigar. Checked the spark plugs after and all had a little oil on them and carbon on the tip. Checked down into the combustion chamber and did not see any flooded cylinders.
I have attached my most current .msq file. Is my issue most likely a setting(s) in Tunerstudio or something with the installation of parts? Should I look over all of the grounding points I used? I have heard that mentioned as being highly important. Thanks.
Got the AIT sensor wired correctly, connected the fuel pump relay wires (Runs when in On position) and downloaded the provided .inc files. AIT sensor is reading correctly now in Tunerstudio.
Since I got straightened out, I tried starting the car again. No luck. Got the car to crank over nicely and sputter trying to start but could not keep going. Was following the directions per various sources where you are trying to set the timing.
Ended up messing around with the timing trigger angle, CAS position, cranking and after enrichment pulse widths. Seemed to be getting closer but no cigar. Checked the spark plugs after and all had a little oil on them and carbon on the tip. Checked down into the combustion chamber and did not see any flooded cylinders.
I have attached my most current .msq file. Is my issue most likely a setting(s) in Tunerstudio or something with the installation of parts? Should I look over all of the grounding points I used? I have heard that mentioned as being highly important. Thanks.
#24
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I am also wondering if I am going about starting the car and setting the timing correctly.
I would set the fixed angle to +10 degrees, and leave the rest of the settings alone. Then messed with the CAS angle a bit to see what kind of difference what would make. Then adjust the triggle angle up or down to see what difference that made. No starting in any of those situations.
Is this something where my timing is off? Or does it sound like I am short on fuel? or spark?
EDIT: Just noticed that the MS manual says to start the engine, THEN change the fixed angle from -10 to 10 degrees. I did that before trying to start the engine.
Would that make the car start or not start? Thanks.
I would set the fixed angle to +10 degrees, and leave the rest of the settings alone. Then messed with the CAS angle a bit to see what kind of difference what would make. Then adjust the triggle angle up or down to see what difference that made. No starting in any of those situations.
Is this something where my timing is off? Or does it sound like I am short on fuel? or spark?
EDIT: Just noticed that the MS manual says to start the engine, THEN change the fixed angle from -10 to 10 degrees. I did that before trying to start the engine.
Would that make the car start or not start? Thanks.
#26
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Will have to get back to you on this one. Don't have my laptop with me at work today. I know initially I reduced it by a factor of (230/460) or multiply by .5 & added 1ms back in based on whatever guide I was reading at the time. Then last night, I tried increasing it by .4 or .5 at a time in each cell. Did that maybe twice. Seems to help a bit to keep sputtering for a second but would still die out.
Also tried the same strategy with the after enrichment pulsewidths.
Also tried the same strategy with the after enrichment pulsewidths.
#28
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Tried starting the car again tonight with no success. Basically the same as yesterday. Took this video to give you guys an idea of what it sounds like and what it's doing.
Miata Engine Start Attempt - YouTube
We got a spark tester and verified that all the coils are sparking. Also checked by listening to the injectors and all seem to be opening.
Here was a thought though, could I not be getting a good fire from the spark plug? They are the NGK 7 temp plugs, gapped to .040" as they come out of the box.
Miata Engine Start Attempt - YouTube
We got a spark tester and verified that all the coils are sparking. Also checked by listening to the injectors and all seem to be opening.
Here was a thought though, could I not be getting a good fire from the spark plug? They are the NGK 7 temp plugs, gapped to .040" as they come out of the box.
#29
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Any ideas guys?? I would like to get the car started ASAP and am running out of troubleshooting ideas. Would it help for me to do a datalog during cranking and upload it here?
Is the information I have provided helpful? Any issues that are plain to see in the msq? Thanks.
Is the information I have provided helpful? Any issues that are plain to see in the msq? Thanks.
#31
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Have not tried jamming the throttle open while cranking it over.
Would fueling mean working on the cranking/prime table to get more fuel in or the VE table? Basically not getting enough fuel? I have been checking the cylinders after each time at it and they are not flooded yet.
Would fueling mean working on the cranking/prime table to get more fuel in or the VE table? Basically not getting enough fuel? I have been checking the cylinders after each time at it and they are not flooded yet.
#32
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
not during, after cranking. the car technically starts, it just wont stay running.
which makes me think your ve fuel table, ASE table, and/or warmup tables are messed up.
i dont think you have enough fuel after it catches.
which makes me think your ve fuel table, ASE table, and/or warmup tables are messed up.
i dont think you have enough fuel after it catches.
#33
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Do you think my spark plug gap is too large, .040", and might be causing an issue as well? Just want to check it off the list if not applicable.
#35
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Hopefully I can get it to stay on so far. Glad that nobody has come back large red flags telling I should stop breaking things with such terrible settings
![big grin](https://www.miataturbo.net/images/smilies/biggrin.gif)
#37
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Will try. Is that also something I could adjust on TS? I have the TPS unplugged right now and the calibration doesn't work to my knowledge. Also won't let me input 255 for start/stop positions like detailed on boostedmiata.
#39
Junior Member
Thread Starter
iTrader: (3)
Join Date: Apr 2010
Location: South Bay, CA
Posts: 351
Total Cats: -2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Cranking, ASE and VE Table 1 shown in images in post #27. Req_fuel calculated at 7.0 for the RX-7 460cc injectors @ 12.7 AFR.
TPS is stock, so not variable, and unplugged currently.
TPS is stock, so not variable, and unplugged currently.