JimStim Help
#1
JimStim Help
Pointers on where to find notes on use of the Stims would be GREATLY appreciated. I have a DIY MS3 kit, with 3X card. Stim for main board and 3X card.
Tuner Studio shows inputs from:
AFR, Manifold Air Temp, Coolant Temp and TPS.
No reaction for RPM, either coarse or fine adjustment.
Since I have a new MS3 and new Stims, I guess issues could be in either one or even both. Not sure where to go from here
Tuner Studio shows inputs from:
AFR, Manifold Air Temp, Coolant Temp and TPS.
No reaction for RPM, either coarse or fine adjustment.
Since I have a new MS3 and new Stims, I guess issues could be in either one or even both. Not sure where to go from here
#3
Hey - is anyone allowed to see your Exocet build? I've been kicking around the idea of one myself - but only thinking about it so far. Would love to see one in the flesh (fiberglass?)!
#4
Per tips from Matt, I have verified 3 jumpers from the JimStim to the JimStimX:
5V from Stim to StimX - this was connected.
Ground from Stim to StimX - Did not have this before
Jumper from 2nd Trigger on Stim to Cam on StimX - did not have this before
Made the two changes, but still no RPM signal showing up on the TS screen.
5V from Stim to StimX - this was connected.
Ground from Stim to StimX - Did not have this before
Jumper from 2nd Trigger on Stim to Cam on StimX - did not have this before
Made the two changes, but still no RPM signal showing up on the TS screen.
#5
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
Are you saying I should have Firmware V2.0? The chip on the Stim is marked V2.0.3 which I guess is newer than V2.0? My JimStim Kit came from you guys back in fall of 2011. Or are there directions somewhere under the heading of "JimStim Firmware V2.0"?
Hey - is anyone allowed to see your Exocet build? I've been kicking around the idea of one myself - but only thinking about it so far. Would love to see one in the flesh (fiberglass?)!
Hey - is anyone allowed to see your Exocet build? I've been kicking around the idea of one myself - but only thinking about it so far. Would love to see one in the flesh (fiberglass?)!
I don't have any body panels for the Exocet yet. I'm getting the 2014 panels, yet to be released.
#6
Since my last post, I've put the dang thing back in the box for a while. I'm liable to turn it back into its constituent silicon bits due to my high level of frustration.
I did click on that link you suggested. I've been to that site before, mainly when I built the thing. Good info. One thing I did verify, is that the JimStim itself seems to be good. I went through the setup guide, and all LED's work, and the CPU seems OK as I could get one of the LED's flashing when tested. Rate of flashing changed with RPM. Still nada on rpm when hooked up to the MS3 and Tuner Studio. Do have other functions working, coolant, O2 etc.
As good as that info is however, I still don't know why I have no RPM signal on TS. Hopefully a composite log I tried to send to Matt and Brian will show them something I've done wrong or am missing.
I did click on that link you suggested. I've been to that site before, mainly when I built the thing. Good info. One thing I did verify, is that the JimStim itself seems to be good. I went through the setup guide, and all LED's work, and the CPU seems OK as I could get one of the LED's flashing when tested. Rate of flashing changed with RPM. Still nada on rpm when hooked up to the MS3 and Tuner Studio. Do have other functions working, coolant, O2 etc.
As good as that info is however, I still don't know why I have no RPM signal on TS. Hopefully a composite log I tried to send to Matt and Brian will show them something I've done wrong or am missing.
Thread
Thread Starter
Forum
Replies
Last Post