Gm IAT wires not same as in instructions. urgemt
#1
Senior Member
Thread Starter
iTrader: (3)
Join Date: Sep 2011
Location: Plano TX
Posts: 595
Total Cats: -1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So mounted the iat in itercooler worked like a charm.
Now go to wire it to the old maf and the electrical hook ups dont match pics on diyautotune instructions. We can over come this by just figuring out which wire are which using an ohm meter. On the ms there is a iat pin so that where one of the wire goes but where does the other go sensor ground or something else.
my maf elect connector has 7 pins.
Now go to wire it to the old maf and the electrical hook ups dont match pics on diyautotune instructions. We can over come this by just figuring out which wire are which using an ohm meter. On the ms there is a iat pin so that where one of the wire goes but where does the other go sensor ground or something else.
my maf elect connector has 7 pins.
#2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Do yourself a favor, stop, search, and roll. Well, stop and search.
http://www.megasquirtpnp.com/models/...#Section_Three
Took me one search to find.
http://www.megasquirtpnp.com/models/...#Section_Three
Took me one search to find.
#3
Boost Pope
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,339
Total Cats: 6,793
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Now go to wire it to the old maf and the electrical hook ups dont match pics on diyautotune instructions. We can over come this by just figuring out which wire are which using an ohm meter. On the ms there is a iat pin so that where one of the wire goes but where does the other go sensor ground or something else.
my maf elect connector has 7 pins.
my maf elect connector has 7 pins.
The picture you want is a little over halfway down the page.
#4
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
![](http://www.megasquirtpnp.com/models/mm9093/mspnp_mm9093_manual/images/image022.jpg)
use these two positions.
The black wire is actually the AIT signal pin, and the red wire is the ground...doesn't matter which is which.
Last edited by Braineack; 01-21-2012 at 11:07 AM.
#5
Senior Member
Thread Starter
iTrader: (3)
Join Date: Sep 2011
Location: Plano TX
Posts: 595
Total Cats: -1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
sorry I did search 1.6 maf and got nothing. I appreciate the help i was using this link for the instruction
http://www.diyautotune.com/diypnp/ap...3-16b6-mt.html
http://www.diyautotune.com/diypnp/ap...3-16b6-mt.html
#6
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
they used the wrong picture. the one i pulled was from the mspnp docs: http://www.megasquirtpnp.com/models/...093_manual.htm
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM
Mikel
MEGAsquirt
4
09-28-2015 04:46 PM