When you click on links to various merchants on this site and make a purchase, this can result in this site earning a commission. Affiliate programs and affiliations include, but are not limited to, the eBay Partner Network.
short history, its a 99 engine in a 93 shell. ran well on stock ecu. started with megasquirt. while setting trigger angle, after 4-5 flashes, car wouldnt start anymore. on stock ecu, wouldnt start, culprit was burnt coil pack.
so i do a cop conversion, 1.6 ignitor hard wired to the coils. runs great on stock ecu, but on the ms i cant get any spark... megasquirt logs show rpm around 260 cranking, injectors firing, just no spark..
What MS are you running? If it's MS2 or 3, put it in test mode and try and test the spark outputs, but if they aren't working, you most likely fried some hardware when the coil went out.
What MS are you running? If it's MS2 or 3, put it in test mode and try and test the spark outputs, but if they aren't working, you most likely fried some hardware when the coil went out.
its a ms1 v3, if something on the board fried shouldnt it look/smell burnt?
it says R37 and R38 slots should be bip373 on my ms it has tk20p in r38 it looked lifted off the heatsink, i tried to press it down and one of the leads cracked. may be able to solder back, but is this what would be burnt from coil driver? i dont mind replacing but dont want to waste time waiting for parts if its not suspect
can anyone at least tell me which mods are done to this ms? i tried with spare coil pack and ignitor and it works... it doesnt work with my cop setup... id like to demod the ms, then add mods as i need.
well flashing without disconnecting the coils is what fried the ignitor in the first place. as far as the new cops not working? I dunno, how poorly/incorrectly did you build the harness?
well flashing without disconnecting the coils is what fried the ignitor in the first place. as far as the new cops not working? I dunno, how poorly/incorrectly did you build the harness?
can anyone at least tell me which mods are done to this ms? i tried with spare coil pack and ignitor and it works... it doesnt work with my cop setup... id like to demod the ms, then add mods as i need.
when measuring voltage at the cop wiring, i see +12v on the positive and trigger wires with the stock ecu
with the megasquirt plugged in i get +12 on the positive but not on the trigger.
i also found an issue in the megasquirt wiring, pin 31 and 36 were on the spark a and b outputs, and it should be pin 6 and 36, so i switched those and gave it a crank but didnt fire.
hope to get more time to mess with it tommorrow or sunday....
You're all over the place. The car ran on stock coils + MS. Then you changed things, and it didn't anymore. So you put COPs on it, and it still didn't. Then you swapped ECUs, and... a coil i think? And it worked with both COPs and oem coils on stock ecu. And then oem coils + MS again. But COPs only work on stock ecu, not MS.
it was on stock coils and ms, it was running very rough due to what i assumed was the trigger angle. after a few trigger angle adjustments, it wouldnt run anymore. i put back the stock ecu, and it was running rough. diagnosis here was 1 coil went bad.
i switched to cops and back to stock ecu. it runs like stock on cops and stock ecu. it doesnt spark with megasquirt and cops. im testing by using a spark plug wire between plug and a coil and using a timing light. i tried another set of coils/igniter, and it ran but rough. this running rough was its only firing on 2 cylinders. i didnt know at the time it wasnt the trigger angle setting.
i contacted diyautotune, and they said test the voltages at the end of wiring at the cops. the difference being, with the ms, i dont get any voltage on the trigger wire. so i looked at the db37 to ecu connection, and pins 31 and 36 were wired to the ignition pins (1G 1H on the ecu connector). so i swapped pin 6 which assembly manual says should be used with pin 31 which should control iac.
unplugged everything, testing trigger wire the ms to ignition outputs were correct before. pin 31 and 36. 5v on each. checked at the igniter factory plug, still 5v. checked at end of cops wires still 5v. when plugging in the cops, voltage drops to 1.76 on each. they need a 5v signal to fire if im correct.
so you guys are correct the cops/wiring are the issue.
so my question, where did i go wrong in my wiring..
wire colors are on the factory igniter wiring (gutted an igniter to pnp)
trigger for 1+4 runs to brown/yellow
trigger 2+3 runs to brown
12v runs to blue
ground runs to black, and grounds on firewall
tach splices together all 4 coils, runs to yellow/blue and black/white
I mean... Ya got 4 wires at each coil: 5v signal, signal gnd, +B, and power gnd. Make sure you put sig gnd back to the MS, and power gnd back to the motor.
Test correct firing order using the diagnostic tool:
A->1
B->3
C->4
D->2
so it seems the cop i have need 12v to trigger. the ms only gives them 5v. the stock ecu gives them 12v.
can i just do a pullup to 12v instead of 5v on the megasquirt? i tried to move the resistor pulling off the 5v above the proto area to the 12v leg of U5, but the output was still 5v after powering up on jimstim.
they are toyota 1zz plugs, but def not oem. im going to try a local junkyard for some oem plugs this friday. after a bit of thinking, i rather have a common 5v triggered plug and no mods on ms, instead of trying to find another one of these later if one goes bad