Brain DIYPNP map on MSPNP2
#42
The valve setting is like that on the DIY auto tune basemap. It was like this with my map as well. I changed it & it started idling much better.
I don't have the technical knowledge like you with compensating things. like one thing is the same as the other.Yes I understand there is 10 different ways to do one thing.
If this was me....I would stop compensating. or changing things go to the basics. If you are a practiced tuner....that's different.
save your current map.
start a new project.
insert all the correct numbers in the fuel calculation
set your CAS at 10 deg
set your trigger angle at 10
do the trigger wizzard
start with open loop warm up
change the valve mode to normal
adjust your valve frequency to your correct idle yours is currently set at 480.....seems a little high Mine is at 180 something....
lower your cranking RPM a bit
If you get it going.....and its Ok get the idle stable.
if then you choose to go closed loop. do the Idle valve test
Its going to take you 15 minutes. If its the same as before.....your allowed to sledge me openly.
if it works there are some good articles on setting closed loop idle settings which are very understandable compared to the instructions of MS.
I found getting the idle valve to run correctly made the car run so much better overall......even though it only supposed to affect the idle.
IMHO.....getting the valve correct at the beginning.....will make things so much nicer in the long run with the tune
I don't have the technical knowledge like you with compensating things. like one thing is the same as the other.Yes I understand there is 10 different ways to do one thing.
If this was me....I would stop compensating. or changing things go to the basics. If you are a practiced tuner....that's different.
save your current map.
start a new project.
insert all the correct numbers in the fuel calculation
set your CAS at 10 deg
set your trigger angle at 10
do the trigger wizzard
start with open loop warm up
change the valve mode to normal
adjust your valve frequency to your correct idle yours is currently set at 480.....seems a little high Mine is at 180 something....
lower your cranking RPM a bit
If you get it going.....and its Ok get the idle stable.
if then you choose to go closed loop. do the Idle valve test
Its going to take you 15 minutes. If its the same as before.....your allowed to sledge me openly.
if it works there are some good articles on setting closed loop idle settings which are very understandable compared to the instructions of MS.
I found getting the idle valve to run correctly made the car run so much better overall......even though it only supposed to affect the idle.
IMHO.....getting the valve correct at the beginning.....will make things so much nicer in the long run with the tune
#43
The valve setting is like that on the DIY auto tune basemap. It was like this with my map as well. I changed it & it started idling much better.
I don't have the technical knowledge like you with compensating things. like one thing is the same as the other.Yes I understand there is 10 different ways to do one thing.
If this was me....I would stop compensating. or changing things go to the basics. If you are a practiced tuner....that's different.
save your current map.
start a new project.
insert all the correct numbers in the fuel calculation
set your CAS at 10 deg
set your trigger angle at 10
do the trigger wizzard
start with open loop warm up
change the valve mode to normal
adjust your valve frequency to your correct idle yours is currently set at 480.....seems a little high Mine is at 180 something....
lower your cranking RPM a bit
If you get it going.....and its Ok get the idle stable.
if then you choose to go closed loop. do the Idle valve test
Its going to take you 15 minutes. If its the same as before.....your allowed to sledge me openly.
if it works there are some good articles on setting closed loop idle settings which are very understandable compared to the instructions of MS.
I found getting the idle valve to run correctly made the car run so much better overall......even though it only supposed to affect the idle.
IMHO.....getting the valve correct at the beginning.....will make things so much nicer in the long run with the tune
I don't have the technical knowledge like you with compensating things. like one thing is the same as the other.Yes I understand there is 10 different ways to do one thing.
If this was me....I would stop compensating. or changing things go to the basics. If you are a practiced tuner....that's different.
save your current map.
start a new project.
insert all the correct numbers in the fuel calculation
set your CAS at 10 deg
set your trigger angle at 10
do the trigger wizzard
start with open loop warm up
change the valve mode to normal
adjust your valve frequency to your correct idle yours is currently set at 480.....seems a little high Mine is at 180 something....
lower your cranking RPM a bit
If you get it going.....and its Ok get the idle stable.
if then you choose to go closed loop. do the Idle valve test
Its going to take you 15 minutes. If its the same as before.....your allowed to sledge me openly.
if it works there are some good articles on setting closed loop idle settings which are very understandable compared to the instructions of MS.
I found getting the idle valve to run correctly made the car run so much better overall......even though it only supposed to affect the idle.
IMHO.....getting the valve correct at the beginning.....will make things so much nicer in the long run with the tune
#46
Boost Czar
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
that's not the issue. 500rpm is fine -- the lower it is, the harder time youll have in the cold. but 500rpm is probably the upper limit.
from the "oddlog" it's running REALLLY rich when you start it up
#51
The main things I see in the cold start log you posted:
Are the temperture readings correct? Maybe Indiana's having a really cold May, but make sure those numbers are accurate.
You may also need to adjust the cold cranking pulse widths.
Your battery is nearly dead.
I'd turn off closed loop idle control until you are further along in the tuning process.
Are the temperture readings correct? Maybe Indiana's having a really cold May, but make sure those numbers are accurate.
You may also need to adjust the cold cranking pulse widths.
Your battery is nearly dead.
I'd turn off closed loop idle control until you are further along in the tuning process.
#52
The main things I see in the cold start log you posted:
Are the temperture readings correct? Maybe Indiana's having a really cold May, but make sure those numbers are accurate.
You may also need to adjust the cold cranking pulse widths.
Your battery is nearly dead.
I'd turn off closed loop idle control until you are further along in the tuning process.
Are the temperture readings correct? Maybe Indiana's having a really cold May, but make sure those numbers are accurate.
You may also need to adjust the cold cranking pulse widths.
Your battery is nearly dead.
I'd turn off closed loop idle control until you are further along in the tuning process.