99/00 MS diy pnp no CLT/MAT reading.
#1
Elite Member
Thread Starter
iTrader: (30)
Join Date: Aug 2007
Location: Va Beach
Posts: 7,329
Total Cats: 12
99/00 MS diy pnp no CLT/MAT reading.
Got a friends PNP here from the enhanced group buy. Got it installed and car running. Not getting CLT/MAT reading what so ever. I burned the readings that are already in the MS and also burned the settings from here
http://www.diyautotune.com/diypnp/ap...0-18bp-mt.html
CLT reads 180 no matter what setting are loaded and MAT is at 70. Was on phone with Brain and we went over all the wiring inside the MS and everything seems to be correct.
Also, which might be related to the CLT not reading, the main fan doesn't work.
Any ideas?
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
http://www.diyautotune.com/diypnp/ap...0-18bp-mt.html
CLT reads 180 no matter what setting are loaded and MAT is at 70. Was on phone with Brain and we went over all the wiring inside the MS and everything seems to be correct.
Also, which might be related to the CLT not reading, the main fan doesn't work.
Any ideas?
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#3
Elite Member
Thread Starter
iTrader: (30)
Join Date: Aug 2007
Location: Va Beach
Posts: 7,329
Total Cats: 12
It's hooked up, no idea if it's working. It is brand new.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#4
Elite Member
Thread Starter
iTrader: (30)
Join Date: Aug 2007
Location: Va Beach
Posts: 7,329
Total Cats: 12
Another note, when you first start the car, the a/c compressor and fans will come on for only about 10 seconds. They will not come on again unless I cycle the ignition but only for about 10 seconds.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#5
Elite Member
iTrader: (10)
Join Date: Jun 2006
Location: Athens, Greece
Posts: 5,990
Total Cats: 361
Verify that SG is on 4C and 4F. Brain told me he had it on 4G, which is wrong. Also check for 5V on 3I. Is the expansion board grounded properly though one of the GND pads on the mainboard (it must *NOT* be connected to any of the GND pads on the connectorboard).
#6
Elite Member
Thread Starter
iTrader: (30)
Join Date: Aug 2007
Location: Va Beach
Posts: 7,329
Total Cats: 12
Okay, we'll have to pull it apart again.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#8
Elite Member
Thread Starter
iTrader: (30)
Join Date: Aug 2007
Location: Va Beach
Posts: 7,329
Total Cats: 12
Okay, what's your email. Going to be later this evening before we get back on the car.
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#10
Elite Member
Thread Starter
iTrader: (30)
Join Date: Aug 2007
Location: Va Beach
Posts: 7,329
Total Cats: 12
SG to 4F was nonexistent. Put in the wire and the MS works perfectly now.
Thanks!
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
Thread
Thread Starter
Forum
Replies
Last Post
Zaphod
MEGAsquirt
47
10-26-2018 11:00 PM