Toys! Glorious toys! SAD FACE :(
#61
Boost Czar
Thread Starter
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,729
Total Cats: 4,126
I'll try that before pulling the head...
what made it worse was i started with a small hole and decided to step it up so the bit wouldn't snap off...
Dirlling the stud was easy, so if i can get the hardened junk out I should be able to start from square one again. Are left-handed drill bits common at the major stores?
what made it worse was i started with a small hole and decided to step it up so the bit wouldn't snap off...
Dirlling the stud was easy, so if i can get the hardened junk out I should be able to start from square one again. Are left-handed drill bits common at the major stores?
#62
I've never seen an extractor work. I've heard countless people break them off in the work though.
But seriously, left hand drill bits are awesome. Assuming you didn't already have an extractor broke off in the work , you just center punch the broken fastener making SURE you get punch it dead nuts center. Get out your left hand drill bit set you bought at autozone for 10 bucks. Then drill a pilot hole. Use a bit bigger than 1/8" if it's grade 5 or 8 as to not break the bit. Start drilling one size at a time, keep it square, etc. When you get to that last bit that will drill before wiping out the threads, drill it about 2/3 of the way through the fastener and then jam the bit, forcing it to dig into the fastener. It will likely hang up and either stop the drill, break the bit, or screw the fastener out. I've got ~50% success rate of it screwing the fastener out. Then your done. If not, drill out the bolt and threads completely. Then tap. Then helicoil. Now it's stronger than new because helicoils are the ****.
But seriously, left hand drill bits are awesome. Assuming you didn't already have an extractor broke off in the work , you just center punch the broken fastener making SURE you get punch it dead nuts center. Get out your left hand drill bit set you bought at autozone for 10 bucks. Then drill a pilot hole. Use a bit bigger than 1/8" if it's grade 5 or 8 as to not break the bit. Start drilling one size at a time, keep it square, etc. When you get to that last bit that will drill before wiping out the threads, drill it about 2/3 of the way through the fastener and then jam the bit, forcing it to dig into the fastener. It will likely hang up and either stop the drill, break the bit, or screw the fastener out. I've got ~50% success rate of it screwing the fastener out. Then your done. If not, drill out the bolt and threads completely. Then tap. Then helicoil. Now it's stronger than new because helicoils are the ****.
#64
Boost Czar
Thread Starter
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,729
Total Cats: 4,126
I've never seen an extractor work. I've heard countless people break them off in the work though.
But seriously, left hand drill bits are awesome. Assuming you didn't already have an extractor broke off in the work , you just center punch the broken fastener making SURE you get punch it dead nuts center. Get out your left hand drill bit set you bought at autozone for 10 bucks. Then drill a pilot hole. Use a bit bigger than 1/8" if it's grade 5 or 8 as to not break the bit. Start drilling one size at a time, keep it square, etc. When you get to that last bit that will drill before wiping out the threads, drill it about 2/3 of the way through the fastener and then jam the bit, forcing it to dig into the fastener. It will likely hang up and either stop the drill, break the bit, or screw the fastener out. I've got ~50% success rate of it screwing the fastener out. Then your done. If not, drill out the bolt and threads completely. Then tap. Then helicoil. Now it's stronger than new because helicoils are the ****.
But seriously, left hand drill bits are awesome. Assuming you didn't already have an extractor broke off in the work , you just center punch the broken fastener making SURE you get punch it dead nuts center. Get out your left hand drill bit set you bought at autozone for 10 bucks. Then drill a pilot hole. Use a bit bigger than 1/8" if it's grade 5 or 8 as to not break the bit. Start drilling one size at a time, keep it square, etc. When you get to that last bit that will drill before wiping out the threads, drill it about 2/3 of the way through the fastener and then jam the bit, forcing it to dig into the fastener. It will likely hang up and either stop the drill, break the bit, or screw the fastener out. I've got ~50% success rate of it screwing the fastener out. Then your done. If not, drill out the bolt and threads completely. Then tap. Then helicoil. Now it's stronger than new because helicoils are the ****.
I have had success with an extractor before:
that's actually the one I broke today.
#71
I'm also all for hammering the extractor to pieces. I doubt there is much of it in there anyway. Then left hand drilling to try and get the pieces out with the intent of heli-coiling the hole if there is even a question of it being messed up. After using about 200 helicoils at work in delrin tooling and aluminum baseplates I love them.
I have use extractors successfully. Though I have had way more luck with small cold chisels.
Any chance the stud is sticking out a little for you to dremel a slot? The abrasive wheel will cut into that hardened extractor, it'll just take forever to do right.
I have use extractors successfully. Though I have had way more luck with small cold chisels.
Any chance the stud is sticking out a little for you to dremel a slot? The abrasive wheel will cut into that hardened extractor, it'll just take forever to do right.
#72
Boost Czar
Thread Starter
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,729
Total Cats: 4,126
exactly, i might as well try breaking the bit up and going at it again. otherwise I pull the head and get it fixed at a machine shop. but in the meantime I'll slap my spare head on so i can acutally have a running car.
#73
Boost Czar
Thread Starter
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,729
Total Cats: 4,126
here's my seat...I put it on the stock rails. You can see how it's just too large. Even if I bolt it to the floor it's just not going to be ideal, so tomorrow they'll be sold.
#77
Cpt. Slow
iTrader: (25)
Join Date: Oct 2005
Location: Oregon City, OR
Posts: 14,429
Total Cats: 1,207
shouldn't be using those harnesses with those seats anyways. You need a fixed back and 5 harness holes, anything else is useless. What fixed back seat did you end up buying?
Sorry about the extractor breaking, the first time I used one it worked, so I bought a complete set, thinking they were awesome. I've broken most of those without ever getting a stuck bolt out since.
Sorry about the extractor breaking, the first time I used one it worked, so I bought a complete set, thinking they were awesome. I've broken most of those without ever getting a stuck bolt out since.
Thread
Thread Starter
Forum
Replies
Last Post
StratoBlue1109
Miata parts for sale/trade
21
09-30-2018 01:09 PM
JesseTheNoob
DIY Turbo Discussion
15
09-30-2015 02:44 PM