Time for Turbo Rebuild?
#1
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Well....car has 1200 miles on it now.
The car has been running great, but today I was fine tuning my 20 psi tune (adding a little timing
).
After that, I stopped to adjust my two-step. I had the two-step at 4500 making 3psi.....not much. Messed with a few setting and got it up to 10psi.
Immediately after that, the turbo started making noise (not metal on metal, but a very very noticeably "hum"). Stopped and killed then engine, pulled the Air Filter off to check out the shaft and found quite a bit of side to side movement when moving the compressor wheel.
So, I set off to get home. About 2 miles before I got to my house I started to here metal on metal contact, but only about 5 seconds or so when I was almost stopped at a stop light (as the turbo was slowing down). It seemed like it would make more noise with less load. If I gave it a little throttle, it would actually get quieter (as far the new turbo sounds).
I guess if I need to rebuild it, I will order the stuff tomorrow. Fun Fun
The car has been running great, but today I was fine tuning my 20 psi tune (adding a little timing
![](https://www.miataturbo.net/images/smilies/smile.gif)
After that, I stopped to adjust my two-step. I had the two-step at 4500 making 3psi.....not much. Messed with a few setting and got it up to 10psi.
Immediately after that, the turbo started making noise (not metal on metal, but a very very noticeably "hum"). Stopped and killed then engine, pulled the Air Filter off to check out the shaft and found quite a bit of side to side movement when moving the compressor wheel.
So, I set off to get home. About 2 miles before I got to my house I started to here metal on metal contact, but only about 5 seconds or so when I was almost stopped at a stop light (as the turbo was slowing down). It seemed like it would make more noise with less load. If I gave it a little throttle, it would actually get quieter (as far the new turbo sounds).
I guess if I need to rebuild it, I will order the stuff tomorrow. Fun Fun
#2
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Well....car has 1200 miles on it now.
The car has been running great, but today I was fine tuning my 20 psi tune (adding a little timing
).
After that, I stopped to adjust my two-step. I had the two-step at 4500 making 3psi.....not much. Messed with a few setting and got it up to 10psi.
Immediately after that, the turbo started making noise (not metal on metal, but a very very noticeably "hum"). Stopped and killed then engine, pulled the Air Filter off to check out the shaft and found quite a bit of side to side movement when moving the compressor wheel.
So, I set off to get home. About 2 miles before I got to my house I started to here metal on metal contact, but only about 5 seconds or so when I was almost stopped at a stop light (as the turbo was slowing down). It seemed like it would make more noise with less load. If I gave it a little throttle, it would actually get quieter (as far the new turbo sounds).
I guess if I need to rebuild it, I will order the stuff tomorrow. Fun Fun
The car has been running great, but today I was fine tuning my 20 psi tune (adding a little timing
![](https://www.miataturbo.net/images/smilies/smile.gif)
After that, I stopped to adjust my two-step. I had the two-step at 4500 making 3psi.....not much. Messed with a few setting and got it up to 10psi.
Immediately after that, the turbo started making noise (not metal on metal, but a very very noticeably "hum"). Stopped and killed then engine, pulled the Air Filter off to check out the shaft and found quite a bit of side to side movement when moving the compressor wheel.
So, I set off to get home. About 2 miles before I got to my house I started to here metal on metal contact, but only about 5 seconds or so when I was almost stopped at a stop light (as the turbo was slowing down). It seemed like it would make more noise with less load. If I gave it a little throttle, it would actually get quieter (as far the new turbo sounds).
I guess if I need to rebuild it, I will order the stuff tomorrow. Fun Fun
#4
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Not sure exactly what turbo you have right now, my memory isn't that good. gpopshop.com sells rebuild kits for a good price and they supposedly ship fast.
What kind of oil feed system do you have? What size AN feed line and are you running a restrictor, .060 is what's commonly used.
What kind of oil feed system do you have? What size AN feed line and are you running a restrictor, .060 is what's commonly used.
No Restictor. I want to say it is about 3/16" Line.
#6
Elite Member
iTrader: (22)
Join Date: Dec 2006
Location: Sunny Spanish speaking Non US Caribbean
Posts: 3,224
Total Cats: 3
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
At least you're in good hands with Chad and company. BTW, loved your video with the C5.
Check braineack's how to for additional info. Knowing you I'm sure you won't need it.
Check braineack's how to for additional info. Knowing you I'm sure you won't need it.
#7
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I would run a restrictor with that turbo, spend the money on the fitting from ATP turbo. I'll get you a link.
Not sure what oil pressure you're maxing out at with the built motor but stock max oil pressure of 90 psi when cold will blow by the seals on some turbos. That's where the restrictors come into play. .060 for journal bearing .030 for ball bearing.
When i bought my car it had some shitty high temp silicone feed line, it cracked and after repairing it my turbo started smoking. A piece of rtv had somehow gotten in the oil system and bypassed the filter or something. Anyway, the thrust bearing had RTV in it when it was disassembled. It was bypassing oil and shaft play was like woah.
#8
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
You're not using steel braided a/n line and AN fittings?
I would run a restrictor with that turbo, spend the money on the fitting from ATP turbo. I'll get you a link.
Not sure what oil pressure you're maxing out at with the built motor but stock max oil pressure of 90 psi when cold will blow by the seals on some turbos. That's where the restrictors come into play. .060 for journal bearing .030 for ball bearing.
When i bought my car it had some shitty high temp silicone feed line, it cracked and after repairing it my turbo started smoking. A piece of rtv had somehow gotten in the oil system and bypassed the filter or something. Anyway, the thrust bearing had RTV in it when it was disassembled. It was bypassing oil and shaft play was like woah.
I would run a restrictor with that turbo, spend the money on the fitting from ATP turbo. I'll get you a link.
Not sure what oil pressure you're maxing out at with the built motor but stock max oil pressure of 90 psi when cold will blow by the seals on some turbos. That's where the restrictors come into play. .060 for journal bearing .030 for ball bearing.
When i bought my car it had some shitty high temp silicone feed line, it cracked and after repairing it my turbo started smoking. A piece of rtv had somehow gotten in the oil system and bypassed the filter or something. Anyway, the thrust bearing had RTV in it when it was disassembled. It was bypassing oil and shaft play was like woah.
#9
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Yeah, that actually sounds pretty low, interesting.
Either way a rebuild is in order. I'm interested to know if you have oil coming out the turbine or the compressor. If not something must have gotten into the oil feed blocking oil flow causing the bearings to wear. Not sure what else would cause premature wear like that.
Either way a rebuild is in order. I'm interested to know if you have oil coming out the turbine or the compressor. If not something must have gotten into the oil feed blocking oil flow causing the bearings to wear. Not sure what else would cause premature wear like that.
#10
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Yeah, that actually sounds pretty low, interesting.
Either way a rebuild is in order. I'm interested to know if you have oil coming out the turbine or the compressor. If not something must have gotten into the oil feed blocking oil flow causing the bearings to wear. Not sure what else would cause premature wear like that.
Either way a rebuild is in order. I'm interested to know if you have oil coming out the turbine or the compressor. If not something must have gotten into the oil feed blocking oil flow causing the bearings to wear. Not sure what else would cause premature wear like that.
I am going to order the "High Performance" Rebuild for it tomorrow. Never rebuilt a turbo before, fairly easy?
#11
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Yeah, really easy to rebuild them. Look in the archives of this forum on the main page. There is a writeup on a T25 and T3 rebuild, you should be able to figure it out from that.
You might want to get a 360* thrust bearing if you're putting that much force on things. The 270* or whatever that comes standard might not be enough for you anymore.
You might want to get a 360* thrust bearing if you're putting that much force on things. The 270* or whatever that comes standard might not be enough for you anymore.
#12
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Yeah, really easy to rebuild them. Look in the archives of this forum on the main page. There is a writeup on a T25 and T3 rebuild, you should be able to figure it out from that.
You might want to get a 360* thrust bearing if you're putting that much force on things. The 270* or whatever that comes standard might not be enough for you anymore.
You might want to get a 360* thrust bearing if you're putting that much force on things. The 270* or whatever that comes standard might not be enough for you anymore.
Thanks
#13
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
That turbo should hold up for thousand upon thousands of miles.
The rebuild won't take you more than 2 hours. That includes cleaning the hell out of everything. Heck you could probably get the turbo off the manifold, rebuild it, and bolt it back on in about 2-2.5 hours. It's easy man.
If gpop wants big money for a 360 thrust look on ebay, they show up for sale on there as well.
The rebuild won't take you more than 2 hours. That includes cleaning the hell out of everything. Heck you could probably get the turbo off the manifold, rebuild it, and bolt it back on in about 2-2.5 hours. It's easy man.
If gpop wants big money for a 360 thrust look on ebay, they show up for sale on there as well.
#14
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
That turbo should hold up for thousand upon thousands of miles.
The rebuild won't take you more than 2 hours. That includes cleaning the hell out of everything. Heck you could probably get the turbo off the manifold, rebuild it, and bolt it back on in about 2-2.5 hours. It's easy man.
If gpop wants big money for a 360 thrust look on ebay, they show up for sale on there as well.
The rebuild won't take you more than 2 hours. That includes cleaning the hell out of everything. Heck you could probably get the turbo off the manifold, rebuild it, and bolt it back on in about 2-2.5 hours. It's easy man.
If gpop wants big money for a 360 thrust look on ebay, they show up for sale on there as well.
#16
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
http://www.atpturbo.com/Merchant2/me..._Code=ATP-OIL1
Wideopentuning (forum member) might be able to get a discount on it as well.
Wideopentuning (forum member) might be able to get a discount on it as well.
#18
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Pulled the turbo out and took it apart (it may never be the same). After inspecting the turbine housing, I noticed that it was covered in carbon except just a part of it was nice clean metal....I assume that the turbine wheel was scraping there. Inspected the turbine wheel and it looks good, so I'm not going to worry about it.
Hopefully I don't run into any problems with the rebuild. I might have already botched it by trying to turn the nut to remove the compressor wheel the wrong direction....status of shaft straightness.... unknown. Still spins freely, but I doubt a minor bend would make it stick. But, on a side note, I know how to take it apart now...so I shouldn't run into the problem again.
Hopefully I don't run into any problems with the rebuild. I might have already botched it by trying to turn the nut to remove the compressor wheel the wrong direction....status of shaft straightness.... unknown. Still spins freely, but I doubt a minor bend would make it stick. But, on a side note, I know how to take it apart now...so I shouldn't run into the problem again.
#20
Junior Member
Thread Starter
iTrader: (7)
Join Date: Apr 2007
Location: South of Houston, Texas
Posts: 327
Total Cats: 0
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I don't own a digital camera....BUT I will say that the opening is only about 1/8" diameter. Seems pretty small to me.
When I get up there Thursday, we can pull the feed line off the turbo and take a pic (if you want).
When I get up there Thursday, we can pull the feed line off the turbo and take a pic (if you want).