Off road coolant reroute.
#1
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (11)
Join Date: Apr 2007
Location: VA Beach
Posts: 1,998
Total Cats: 51
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So I have read the miles of threads on reroute and the concept is good. Whats the simplest and cheapest (Lemons Budget) reroute I can do, it needs no heat, no TB connection...Just cool the engine. I have the motor out of the car and head off.
Thanks Guys!
Thanks Guys!
#2
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Kia Sephia water neck
1 90* hose with about 6" legs from auto parts store
1 s shaped hose
1 18" chrome plumging pipe from homedepot.
Then look up "Spacerless coolant reroute".
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
1 90* hose with about 6" legs from auto parts store
1 s shaped hose
1 18" chrome plumging pipe from homedepot.
Then look up "Spacerless coolant reroute".
__________________
Best Car Insurance | Auto Protection Today | FREE Trade-In Quote
#4
I'm Miserable!
iTrader: (5)
Join Date: Dec 2006
Location: jacksonville, fl
Posts: 1,711
Total Cats: -1
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
i need to post pics of mine. i went to pepboys and bought 2 "quickplugs" (brass plate on top and bottom, rubber in the middle, tighten nut to expand). put a bigger one in the front, and a small one where the tube under the exhuast mani went into the mixing block. took the thermostat and lid and bolted it to the back of the head, then took (2) 2 1/4" flex coolant hoses and ran them from the back of the head to the top of the rad. a small peice of metal pipe with my coolant sensor inside it connected the 2 hoses.
#5
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So why are there like 09384759878907687549847509867w845 x 23 * = x(y) [34][983475] different ways to do a coolant reroute?
Seems to me the general idea is to swap where the upper radiator hose and the rear heater hose go to the block and delete the TB water lines. What's so complicated about that?
Seems to me the general idea is to swap where the upper radiator hose and the rear heater hose go to the block and delete the TB water lines. What's so complicated about that?
#8
Boost Pope
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,340
Total Cats: 6,793
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
IMO, the "best" approach for a street driven car (the best compromise of cooling efficiency and temperature stability vs. simplicity, warmup and heater operation) is to do exactly what Mazda did with the 323:
1- Block the front thermostat outlet, and in the case of the 1.8, install a fitting in the blocking plate to supply water to the oil cooler.
2- Relocate the thermostat to the back of the head, and route its output to the upper radiator hose.
3- Leave the heater core return routed to the mixing manifold as stock, and take the feed for the heater core from a pre-thermostat outlet at the back of the head, with a restrictive orifice in series.
In other words:
1- Block the front thermostat outlet, and in the case of the 1.8, install a fitting in the blocking plate to supply water to the oil cooler.
2- Relocate the thermostat to the back of the head, and route its output to the upper radiator hose.
3- Leave the heater core return routed to the mixing manifold as stock, and take the feed for the heater core from a pre-thermostat outlet at the back of the head, with a restrictive orifice in series.
In other words:
![](http://users.telenet.be/miata/images/coolant_reroute/my_reroute/323_1800_GTR_cooling1.jpg)
#9
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
In all reality (and I'm not trying to ask a stupid question even if it may appear that way, I'm just curious) is it necessary to do the reroute?
I did not have any cooling issues on my car and it's been turbo'd for a lot of miles without issue. It seems simple enough to do, I know it helps, but what happens if you don't? Besides apparently having higher coolant temps in the rear of the engine.
I did not have any cooling issues on my car and it's been turbo'd for a lot of miles without issue. It seems simple enough to do, I know it helps, but what happens if you don't? Besides apparently having higher coolant temps in the rear of the engine.
#12
Boost Pope
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,340
Total Cats: 6,793
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Likewise, in warm climates the Miata is more likely to overheat generally than the 323, since when the thermostat is open, much of the coolant bypasses the engine entirely and heads out to the radiator. Doing this mod will tend to make the engine run cooler when moving at low speeds. As an example, my car never overheated when I lived in SoCal, but in North Carolina in August, it tended to creep up to 220°+.
#13
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Thanks Joe, that makes sense and confirms what I was assuming.
During the hottest days here in GA, with the stock OEM main fan only and the PWR radiator, I only saw 205*F max at cruise. Going into boosted runs of course changed all that.
Now that I'm rebuilding the car and it will have a larger IC and I'm adding A/C, this will probably be a good modification to add to the "to-do" list.
During the hottest days here in GA, with the stock OEM main fan only and the PWR radiator, I only saw 205*F max at cruise. Going into boosted runs of course changed all that.
Now that I'm rebuilding the car and it will have a larger IC and I'm adding A/C, this will probably be a good modification to add to the "to-do" list.
#17
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (11)
Join Date: Apr 2007
Location: VA Beach
Posts: 1,998
Total Cats: 51
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
IMO, the "best" approach for a street driven car (the best compromise of cooling efficiency and temperature stability vs. simplicity, warmup and heater operation) is to do exactly what Mazda did with the 323:
1- Block the front thermostat outlet, and in the case of the 1.8, install a fitting in the blocking plate to supply water to the oil cooler.
2- Relocate the thermostat to the back of the head, and route its output to the upper radiator hose.
3- Leave the heater core return routed to the mixing manifold as stock, and take the feed for the heater core from a pre-thermostat outlet at the back of the head, with a restrictive orifice in series.
In other words:
![](http://users.telenet.be/miata/images/coolant_reroute/my_reroute/323_1800_GTR_cooling1.jpg)
1- Block the front thermostat outlet, and in the case of the 1.8, install a fitting in the blocking plate to supply water to the oil cooler.
2- Relocate the thermostat to the back of the head, and route its output to the upper radiator hose.
3- Leave the heater core return routed to the mixing manifold as stock, and take the feed for the heater core from a pre-thermostat outlet at the back of the head, with a restrictive orifice in series.
In other words:
![](http://users.telenet.be/miata/images/coolant_reroute/my_reroute/323_1800_GTR_cooling1.jpg)
#19
Elite Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (11)
Join Date: Apr 2007
Location: VA Beach
Posts: 1,998
Total Cats: 51
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So got my head back from machine shop today and looked at it. I will not have a heater core so how about moving the thermostat to back (like spacerless reroute) and than hoking up the "cursed" water plug to the return line of the heater core that goes back to front of motor. There fore I would have flow and nothing to drill or tap. Seems too easy? What am I missing?