NA fuse/relay box resistance
#1
Elite Member
Thread Starter
iTrader: (18)
Join Date: Dec 2007
Location: oahu
Posts: 1,787
Total Cats: 6
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Does anybody know what the resistance of the ground going into the fuse/relay box (the one in the engine compartment) should be? I am referring to the black wire that looks like it should be a ground and have very low resistance when checked against the chassis/negative terminal on the battery.
My chassis/engine to battery is .2Ω and the black wire in the fuse/relay box was something like 250KΩ. Is that rite?
My chassis/engine to battery is .2Ω and the black wire in the fuse/relay box was something like 250KΩ. Is that rite?
#5
Elite Member
Thread Starter
iTrader: (18)
Join Date: Dec 2007
Location: oahu
Posts: 1,787
Total Cats: 6
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
It is a 90 and I am trying to make sure all of my grounds in the car are adequate.
To answer my own question the black wire that goes into the fuse/relay box is directly from the positive terminal of the battery and the resistance of it was actually 455KΩ so all is well more or less. Thanks again mt!
To answer my own question the black wire that goes into the fuse/relay box is directly from the positive terminal of the battery and the resistance of it was actually 455KΩ so all is well more or less. Thanks again mt!
Last edited by astroboy; 07-19-2011 at 06:41 PM.
#8
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I didn't see any other goners but ill look again. I should have been more specific, the battery is in the trunk and it moved so that the negative side was touching metal and melted to it. I banged it off and got a new terminal. At that time I was able to start the car no problem. A few days later only the gauges would illuminate and only recently no gauges and no power, it keeps getting worse which is strange. This is when I noticed the fuse. Changed out the fuse and it immediately blew again when I tried to crank the car, wasn't getting gauges to illuminate at this point either. So is there a possible short and the battery is sending too much power to the main fuse? I have no idea how to fix this and the main fuse is $3 something so I don't want to keep blowing them out
#9
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Here are a couple other threads regarding the main fuse. They didn't help much though
Main Fuse Keeps Blowing - MX-5 Miata Forum
Blown main fuse
Main Fuse Keeps Blowing - MX-5 Miata Forum
Blown main fuse
#10
Boost Pope
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,339
Total Cats: 6,793
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
The battery's negative terminal is supposed to be securely bonded to chassis- that's where the negative wire goes.
Under normal circumstances, the fact of the battery's negative terminal coming into contact with chassis would cause absolutely nothing- no sparks, no melting, no current flow.
The fact that yours did means that the wire which goes to the battery negative terminal ISN'T making good contact with chassis ground. So fix that first- repair or replace the battery negative cable.
#11
Elite Member
Thread Starter
iTrader: (18)
Join Date: Dec 2007
Location: oahu
Posts: 1,787
Total Cats: 6
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I was going to say the same thing. Also if you actually banged the battery to get it off the inner fender you may have damaged cells/plates (something to look into once you've fixed your neg terminal problem).
#12
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Ok.
The battery's negative terminal is supposed to be securely bonded to chassis- that's where the negative wire goes.
Under normal circumstances, the fact of the battery's negative terminal coming into contact with chassis would cause absolutely nothing- no sparks, no melting, no current flow.
The fact that yours did means that the wire which goes to the battery negative terminal ISN'T making good contact with chassis ground. So fix that first- repair or replace the battery negative cable.
The battery's negative terminal is supposed to be securely bonded to chassis- that's where the negative wire goes.
Under normal circumstances, the fact of the battery's negative terminal coming into contact with chassis would cause absolutely nothing- no sparks, no melting, no current flow.
The fact that yours did means that the wire which goes to the battery negative terminal ISN'T making good contact with chassis ground. So fix that first- repair or replace the battery negative cable.
Also, I'm an idiot and didn't know about removing the negative side first and putting the negative side on last ya I'm a noob
Last night I also attempted to use the battery out of my GF's car which is a 2012 sonata so the battery is mint and I still got nothing. It's strange that at first I was getting gauges to illuminate but now nothing.
I think because I didn't remove the neg side first etc I may have a short somewhere in the cable? Possibly the alternator shorted?
I almost want to replace the fuse and try to do the correct negative terminal removal/install and see if it works but I don't want to risk popping another fuse ffuuuuu
#13
Boost Pope
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,339
Total Cats: 6,793
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I am really confused by your description.
First, this business of "negative first" has no real impact on the car itself. It's merely a safety precaution to prevent you from shorting out the battery itself by accidentally touching the chassis with the wrench you're using to remove the positiver terminal. But since the negative terminal is so damned hard to reach on a Miata (at least, on an NA) I always remove positive first (or positive only, if I merely need to disconnect the battery for a reason other than removing it) and I simply make sure not to short it out with my wrench.
To recap: It does not matter in which order you remove or install the battery wires.
Also, wires don't "short" internally. By definition, a wire *is* a short.
Now, I'm assuming that it's only the 80A main fuse which is blowing, and none others. Right? That narrows things a bit, as very few things are fed directly by the main fuse.
(And I'm assuming that the reason you get nothing with the Sonata's battery installed is because the fuse blew again, and not because you hooked up that battery backwards or something like that.)
Obviously you can try removing the heavy white wire from the alternator and re-testing. Also, inspect the heavy white wire to make sure it's not shorting to chassis or engine somewhere. (eg: abraded insulation.)
Does the fuse blow immediately, or does it not blow until after you turn on the key? If the latter, the starter solenoid could also be at fault (Black/Red.)
First, this business of "negative first" has no real impact on the car itself. It's merely a safety precaution to prevent you from shorting out the battery itself by accidentally touching the chassis with the wrench you're using to remove the positiver terminal. But since the negative terminal is so damned hard to reach on a Miata (at least, on an NA) I always remove positive first (or positive only, if I merely need to disconnect the battery for a reason other than removing it) and I simply make sure not to short it out with my wrench.
To recap: It does not matter in which order you remove or install the battery wires.
Also, wires don't "short" internally. By definition, a wire *is* a short.
Now, I'm assuming that it's only the 80A main fuse which is blowing, and none others. Right? That narrows things a bit, as very few things are fed directly by the main fuse.
(And I'm assuming that the reason you get nothing with the Sonata's battery installed is because the fuse blew again, and not because you hooked up that battery backwards or something like that.)
Obviously you can try removing the heavy white wire from the alternator and re-testing. Also, inspect the heavy white wire to make sure it's not shorting to chassis or engine somewhere. (eg: abraded insulation.)
Does the fuse blow immediately, or does it not blow until after you turn on the key? If the latter, the starter solenoid could also be at fault (Black/Red.)
#15
Boost Pope
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,339
Total Cats: 6,793
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Why, because it's correct? ![big grin](https://www.miataturbo.net/images/smilies/biggrin.gif)
The main power for the starter is unfused, however the power for the solenoid, which comes through the keyswitch and the clutch-interlock switch, is fused only by the main fuse.
I have no idea what the normal operating current of the starter solenoid is, and pulling enough power through the keyswitch to blow the main fuse would certainly generate some heat, but it's a possibility that can't be ignored.
![big grin](https://www.miataturbo.net/images/smilies/biggrin.gif)
The main power for the starter is unfused, however the power for the solenoid, which comes through the keyswitch and the clutch-interlock switch, is fused only by the main fuse.
I have no idea what the normal operating current of the starter solenoid is, and pulling enough power through the keyswitch to blow the main fuse would certainly generate some heat, but it's a possibility that can't be ignored.
#16
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I am really confused by your description.
First, this business of "negative first" has no real impact on the car itself. It's merely a safety precaution to prevent you from shorting out the battery itself by accidentally touching the chassis with the wrench you're using to remove the positiver terminal. But since the negative terminal is so damned hard to reach on a Miata (at least, on an NA) I always remove positive first (or positive only, if I merely need to disconnect the battery for a reason other than removing it) and I simply make sure not to short it out with my wrench.
To recap: It does not matter in which order you remove or install the battery wires.
Also, wires don't "short" internally. By definition, a wire *is* a short.
Now, I'm assuming that it's only the 80A main fuse which is blowing, and none others. Right? That narrows things a bit, as very few things are fed directly by the main fuse.
(And I'm assuming that the reason you get nothing with the Sonata's battery installed is because the fuse blew again, and not because you hooked up that battery backwards or something like that.)
Obviously you can try removing the heavy white wire from the alternator and re-testing. Also, inspect the heavy white wire to make sure it's not shorting to chassis or engine somewhere. (eg: abraded insulation.)
Does the fuse blow immediately, or does it not blow until after you turn on the key? If the latter, the starter solenoid could also be at fault (Black/Red.)
First, this business of "negative first" has no real impact on the car itself. It's merely a safety precaution to prevent you from shorting out the battery itself by accidentally touching the chassis with the wrench you're using to remove the positiver terminal. But since the negative terminal is so damned hard to reach on a Miata (at least, on an NA) I always remove positive first (or positive only, if I merely need to disconnect the battery for a reason other than removing it) and I simply make sure not to short it out with my wrench.
To recap: It does not matter in which order you remove or install the battery wires.
Also, wires don't "short" internally. By definition, a wire *is* a short.
Now, I'm assuming that it's only the 80A main fuse which is blowing, and none others. Right? That narrows things a bit, as very few things are fed directly by the main fuse.
(And I'm assuming that the reason you get nothing with the Sonata's battery installed is because the fuse blew again, and not because you hooked up that battery backwards or something like that.)
Obviously you can try removing the heavy white wire from the alternator and re-testing. Also, inspect the heavy white wire to make sure it's not shorting to chassis or engine somewhere. (eg: abraded insulation.)
Does the fuse blow immediately, or does it not blow until after you turn on the key? If the latter, the starter solenoid could also be at fault (Black/Red.)
I think I am going to try what you mentioned above and make sure the negative cable is grounded appropriately.
I'm unsure as to when the fuse blows exactly. I got a new one and turned the key and nothing happened, I looked under the hood and of course it was toast.
Indeed only the main black fuse is blowing. I wish there was a knowledgeable North Carolina guy that could come get this thing firing again!
I want to thank you for being patient and helpful. I'd buy ya a beer if I knew you...and if you fixed the problem I'd buy ya a keg
Last edited by TheDriver; 07-23-2012 at 02:43 PM.
#17
Boost Pope
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/smod.png)
iTrader: (8)
Join Date: Sep 2005
Location: Chicago. (The less-murder part.)
Posts: 33,339
Total Cats: 6,793
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
With the engine off, the battery is the only source of voltage (which is just potentially current, really) in the car.
With either terminal removed from the battery, no current can flow anywhere, no matter what is touching what. You can remove the positive terminal from the battery and connect it directly to chassis, and no harm will come of it.
The only things you can't do without potentially causing some damage are:
1: Connect the battery backwards,
2: Create a short-circuit between the positive and negative terminals of the battery, such as by creating a connection between the positive wire and chassis while both are still connected (as with the handle of a wrench), and
3: Attempt to operate the electrical system (especially the starter) while any of the ground straps (engine to body, PPF to body, body to battery negative) are loose, frayed, or otherwise sub-optimal.
I think I am going to try what you mentioned above and make sure the negative cable is grounded appropriately.
I'm unsure as to when the fuse blows exactly. I got a new one and turned the key and nothing happened, I looked under the hood and of course it was toast.
Disconnect the white wire from the alternator, insulate it, and leave it hanging. Try powering the car up (key to ACC, then RUN, but not start) and see if the fuse blows. Inspect that wire carefully.
If everything is working, try starting the car. First with just key to START but without depressing the clutch. Did that blow the fuse? If not, proceed to actually start the engine. Did that blow the fuse? If so, you found the bad circuit. If not, you still found the bad circuit. Either way, you'll have your answer at that point.
#18
Boost Czar
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/admin.png)
iTrader: (62)
Join Date: May 2005
Location: Chantilly, VA
Posts: 79,688
Total Cats: 4,113
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Why, because it's correct? ![big grin](https://www.miataturbo.net/images/smilies/biggrin.gif)
The main power for the starter is unfused, however the power for the solenoid, which comes through the keyswitch and the clutch-interlock switch, is fused only by the main fuse.
I have no idea what the normal operating current of the starter solenoid is, and pulling enough power through the keyswitch to blow the main fuse would certainly generate some heat, but it's a possibility that can't be ignored.
![big grin](https://www.miataturbo.net/images/smilies/biggrin.gif)
The main power for the starter is unfused, however the power for the solenoid, which comes through the keyswitch and the clutch-interlock switch, is fused only by the main fuse.
I have no idea what the normal operating current of the starter solenoid is, and pulling enough power through the keyswitch to blow the main fuse would certainly generate some heat, but it's a possibility that can't be ignored.
see my DD thread.
#20
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
That's a negatory, good buddy.
With the engine off, the battery is the only source of voltage (which is just potentially current, really) in the car.
With either terminal removed from the battery, no current can flow anywhere, no matter what is touching what. You can remove the positive terminal from the battery and connect it directly to chassis, and no harm will come of it.
The only things you can't do without potentially causing some damage are:
1: Connect the battery backwards,
2: Create a short-circuit between the positive and negative terminals of the battery, such as by creating a connection between the positive wire and chassis while both are still connected (as with the handle of a wrench), and
3: Attempt to operate the electrical system (especially the starter) while any of the ground straps (engine to body, PPF to body, body to battery negative) are loose, frayed, or otherwise sub-optimal.
This is a good idea in general, however a bad ground isn't causing your main fuse to blow.
Well, we need to find that out.
Disconnect the white wire from the alternator, insulate it, and leave it hanging. Try powering the car up (key to ACC, then RUN, but not start) and see if the fuse blows. Inspect that wire carefully.
If everything is working, try starting the car. First with just key to START but without depressing the clutch. Did that blow the fuse? If not, proceed to actually start the engine. Did that blow the fuse? If so, you found the bad circuit. If not, you still found the bad circuit. Either way, you'll have your answer at that point.
With the engine off, the battery is the only source of voltage (which is just potentially current, really) in the car.
With either terminal removed from the battery, no current can flow anywhere, no matter what is touching what. You can remove the positive terminal from the battery and connect it directly to chassis, and no harm will come of it.
The only things you can't do without potentially causing some damage are:
1: Connect the battery backwards,
2: Create a short-circuit between the positive and negative terminals of the battery, such as by creating a connection between the positive wire and chassis while both are still connected (as with the handle of a wrench), and
3: Attempt to operate the electrical system (especially the starter) while any of the ground straps (engine to body, PPF to body, body to battery negative) are loose, frayed, or otherwise sub-optimal.
This is a good idea in general, however a bad ground isn't causing your main fuse to blow.
Well, we need to find that out.
Disconnect the white wire from the alternator, insulate it, and leave it hanging. Try powering the car up (key to ACC, then RUN, but not start) and see if the fuse blows. Inspect that wire carefully.
If everything is working, try starting the car. First with just key to START but without depressing the clutch. Did that blow the fuse? If not, proceed to actually start the engine. Did that blow the fuse? If so, you found the bad circuit. If not, you still found the bad circuit. Either way, you'll have your answer at that point.