I think i blew my engine.
#27
Moderator
![](/mt2011/images_td/ranks/supporter1.gif)
![](/mt2011/images_td/ranks/moderator.png)
iTrader: (12)
Join Date: Nov 2008
Location: Tampa, Florida
Posts: 20,885
Total Cats: 3,075
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
That engine is done. Either go get another one from the junkyard or spend a lot on machine work. Whichever is cheaper and easier. If money is plentiful, build it up stronger. That galling on the cylinder wall means that little pieces of piston and maybe rings went through your turbo's exhaust turbine also. Inspect for possible damage. Any pieces may be trapped in front of your cat. Expensive lesson to teach you some restraint. Unfortunate. If you don't have a knock sensor, that may be a helpful investment also...
Some of the valve reliefs on your pistons are very shiny compared to others. Are you seeing evidence of contact there?
Some of the valve reliefs on your pistons are very shiny compared to others. Are you seeing evidence of contact there?
#29
Junior Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (6)
Join Date: Mar 2007
Location: Greece
Posts: 349
Total Cats: -14
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
So guys, i have 2 choices if the engine block can be fixed with overbore pistons.
1. Rebuild with forged internals. (I m wondering if m.tuned rods are ok.)I m thinking of m-tuned rods with wiseco overbore pistons (how much overbore ?)
(off topic)
2.Used motor with thicker head gasket for lower compression.
1. Rebuild with forged internals. (I m wondering if m.tuned rods are ok.)I m thinking of m-tuned rods with wiseco overbore pistons (how much overbore ?)
(off topic)
2.Used motor with thicker head gasket for lower compression.
#32
Junior Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (6)
Join Date: Mar 2007
Location: Greece
Posts: 349
Total Cats: -14
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Hello again! I ordered wiseco pistons with 0.50mm overbore and eagle h-beam rods. How much hp will my engine be able to handle with this setup?
The machinery shop asks 550$ for overboring and fitting the parts. Also I m selling the gt2560 for a gt2876. That failure wasnt so bad at last...
The machinery shop asks 550$ for overboring and fitting the parts. Also I m selling the gt2560 for a gt2876. That failure wasnt so bad at last...
#36
Tour de Franzia
![](/mt2011/images_td/ranks/supporter1.gif)
iTrader: (6)
Join Date: Jun 2006
Location: Republic of Dallas
Posts: 29,085
Total Cats: 375
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
I have a forged motor, 550 injectors, gt2860rs, and I'm afraid to put it past 10psi without getting it to a dyno. lol
That price for machine work is awesome...just make sure you pick a good one.
That price for machine work is awesome...just make sure you pick a good one.
#38
Junior Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (6)
Join Date: Mar 2007
Location: Greece
Posts: 349
Total Cats: -14
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
No need for upgrading the injectors as I m going to work it out with an 8 injectors setup. So 305s+245s= 550s . Brain why do you suggest the 2871 over the 2876 ?
I found one 2876 for cheap.
I found one 2876 for cheap.
#39
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Single injectors would be much more efficient, easier to manage (not to mention install), and support the factory flow characteristics.
The stock injectors are placed where they are for a reason (like placing fuel into the airflow right before the intake valves, and at the proper angle.
Messing with this probably won't turn out ideal, unless you're doing flow analysis on your custom manifold (some have actually done this).
The stock injectors are placed where they are for a reason (like placing fuel into the airflow right before the intake valves, and at the proper angle.
Messing with this probably won't turn out ideal, unless you're doing flow analysis on your custom manifold (some have actually done this).
#40
Junior Member
![](/mt2011/images_td/ranks/supporter1.gif)
Thread Starter
iTrader: (6)
Join Date: Mar 2007
Location: Greece
Posts: 349
Total Cats: -14
![Default](https://www.miataturbo.net/images/icons/icon1.gif)
Single injectors would be much more efficient, easier to manage (not to mention install), and support the factory flow characteristics.
The stock injectors are placed where they are for a reason (like placing fuel into the airflow right before the intake valves, and at the proper angle.
Messing with this probably won't turn out ideal, unless you're doing flow analysis on your custom manifold (some have actually done this).
The stock injectors are placed where they are for a reason (like placing fuel into the airflow right before the intake valves, and at the proper angle.
Messing with this probably won't turn out ideal, unless you're doing flow analysis on your custom manifold (some have actually done this).
Beside this I m running an emanage with the injector restrictions we all know.