clutch works fine. for 10 minutes. then sucks bawlz.
#1
DEI liberal femininity
Thread Starter
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 574
clutch works fine. for 10 minutes. then sucks bawlz.
I'm pretty unsure what's going on since I can't see into the bellhousing but I suspect I have a warped disk or cracked diaphragm spring or something.
Basically I can shift until the car's warm and then I can't get it into ANY gear. I can even feel the car lurch if I try to force it from the syncros engaging.
And before y'all jump on me about clutch hydraulic anything, I did some stroke measurements at the slave (which is new, just like the master) and with the car hot and not shifting, the stroke was within .02" which i doubt is enough to prevent shiftage.
Basically: Argh!
Also basically: i'd rather not have to pull the tranny now and again when I swap motors. heh. how fast can I build a motor? I can have all the parts in-hand in a week or two if I try. Machine work is going to take the longest. Oh and rushing things sucks. Someone sell me a nice 4-door 5-speed E30 for $2000 in teh meantime.
Basically I can shift until the car's warm and then I can't get it into ANY gear. I can even feel the car lurch if I try to force it from the syncros engaging.
And before y'all jump on me about clutch hydraulic anything, I did some stroke measurements at the slave (which is new, just like the master) and with the car hot and not shifting, the stroke was within .02" which i doubt is enough to prevent shiftage.
Basically: Argh!
Also basically: i'd rather not have to pull the tranny now and again when I swap motors. heh. how fast can I build a motor? I can have all the parts in-hand in a week or two if I try. Machine work is going to take the longest. Oh and rushing things sucks. Someone sell me a nice 4-door 5-speed E30 for $2000 in teh meantime.
#5
DEI liberal femininity
Thread Starter
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 574
disks are organic. i hope there's not oil on them... I suppose I can stick a finger in there or something.
magna: this been goin on for maybe a couple months. was sort of an "all of a sudden" thing. no weird sounds.
magna: this been goin on for maybe a couple months. was sort of an "all of a sudden" thing. no weird sounds.
#7
Supporting Vendor
iTrader: (33)
Join Date: Jul 2006
Location: atlanta-ish
Posts: 12,659
Total Cats: 134
bryan--i have every confidence that mr y8s isn't that dumb
also, it typically works the opposite way--the tranny wouldn't work when cold, but would function when hot, if it were low on fluid
my monopoly money is on oily discs
Ben
also, it typically works the opposite way--the tranny wouldn't work when cold, but would function when hot, if it were low on fluid
my monopoly money is on oily discs
Ben
#8
DEI liberal femininity
Thread Starter
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 574
glad I got two spare disks when I bought them last time. but I'm gonna need an erl seal.
ooh or a valve cover gasket because I just had that apart to rig up my COP setup. I wonder if it's draining down the back of the motor onto my junks.
Think I can flood the bellhsg with disk brake cleaner spray?
ooh or a valve cover gasket because I just had that apart to rig up my COP setup. I wonder if it's draining down the back of the motor onto my junks.
Think I can flood the bellhsg with disk brake cleaner spray?
#9
glad I got two spare disks when I bought them last time. but I'm gonna need an erl seal.
ooh or a valve cover gasket because I just had that apart to rig up my COP setup. I wonder if it's draining down the back of the motor onto my junks.
Think I can flood the bellhsg with disk brake cleaner spray?
ooh or a valve cover gasket because I just had that apart to rig up my COP setup. I wonder if it's draining down the back of the motor onto my junks.
Think I can flood the bellhsg with disk brake cleaner spray?
I'm guessing an oily disk swells up when hot, causing friction?
#15
DEI liberal femininity
Thread Starter
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 574
lame update:
ripped the tranny out and the clutch looks relatively normal. maybe a little heat in the pressure plate, floater, and flywheel but otherwise nothing obviously wrong.
I scuffed up all the friction surfaces and set it aside for reassembly. Oh and I'm putting a different ratio pressure plate in to reduce pedal travel a smidge.
So while I had all this **** apart I also decided to swap the ring and pinion. I love anti-seize! But I'm a moron and forgot last time to put the sealant on the diff. I was wondering why it kept dripping oil.
I had to cut off the bearing on the pinion scott sold me. royal pain! I reused the spacer hoping it was within a few thou and not going to cause depth problems. we'll see.
I'll probably start reassembly tomorrow. Time to watch Dr. Strangelove.
ripped the tranny out and the clutch looks relatively normal. maybe a little heat in the pressure plate, floater, and flywheel but otherwise nothing obviously wrong.
I scuffed up all the friction surfaces and set it aside for reassembly. Oh and I'm putting a different ratio pressure plate in to reduce pedal travel a smidge.
So while I had all this **** apart I also decided to swap the ring and pinion. I love anti-seize! But I'm a moron and forgot last time to put the sealant on the diff. I was wondering why it kept dripping oil.
I had to cut off the bearing on the pinion scott sold me. royal pain! I reused the spacer hoping it was within a few thou and not going to cause depth problems. we'll see.
I'll probably start reassembly tomorrow. Time to watch Dr. Strangelove.
#16
DEI liberal femininity
Thread Starter
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 574
Update!
So I've discovered that the failure mode of the Tilton setup is pressure plate warpage. The warp was enough that when it warmed up, it took up too much space in the clutch pack.
Basically as the pressure plate (a separate piece shown in the upper right--the top of the two silver rings) gets heat cycled, the friction surface becomes cone-shaped because of the asymmetry of the metal. The inside circle tries to expand as much as the outside and the result is it pushes the circle out of plane since it has nowhere to go.
I spoke to Tilton about it. They have redesigned the PP to be a little beefier (more heatsink capacity) so hopefully I'll get that iteration when I get my new parts tomorrow.
I also asked them about the "hybrid" cerametallic-organic twins they make. It's exactly the same disks I use from clutchnet (should I sue for stealing my idea?) and has about 70-80% of the engagement properties of the two organic disks but is designed to wear longer. Kinda neat I guess.
M
So I've discovered that the failure mode of the Tilton setup is pressure plate warpage. The warp was enough that when it warmed up, it took up too much space in the clutch pack.
Basically as the pressure plate (a separate piece shown in the upper right--the top of the two silver rings) gets heat cycled, the friction surface becomes cone-shaped because of the asymmetry of the metal. The inside circle tries to expand as much as the outside and the result is it pushes the circle out of plane since it has nowhere to go.
I spoke to Tilton about it. They have redesigned the PP to be a little beefier (more heatsink capacity) so hopefully I'll get that iteration when I get my new parts tomorrow.
I also asked them about the "hybrid" cerametallic-organic twins they make. It's exactly the same disks I use from clutchnet (should I sue for stealing my idea?) and has about 70-80% of the engagement properties of the two organic disks but is designed to wear longer. Kinda neat I guess.
M
#17
DEI liberal femininity
Thread Starter
iTrader: (8)
Join Date: Jun 2005
Location: Fake Virginia
Posts: 19,338
Total Cats: 574
my thread gets no love. so I shall stroke it myself...
put the tranny back in tonight. and amazingly, i didn't even get my hands dirty. nothing under the fingernails. nitrile gloves friggin rock.
so I got the pressure plate that's redesigned to be more beefy. I'd say there's about 20% more mass there so that's cool.
probably finish reassembly on saturday morning.
ok carry on.
put the tranny back in tonight. and amazingly, i didn't even get my hands dirty. nothing under the fingernails. nitrile gloves friggin rock.
so I got the pressure plate that's redesigned to be more beefy. I'd say there's about 20% more mass there so that's cool.
probably finish reassembly on saturday morning.
ok carry on.